OCPN Draw 1.4 available

[rgleason]

Jon I've compiled and tested v1.5.14 using wxwidgets 3.0.2 to be compatible with OpenCPN v4.8.4 and the windows setup file is available on github.

It works. Thank you for your work on this plugin!

[Baikal]

Originally Posted by jongough

Hi,
I now have a windows 10 version of OCPN 4.99 and OD 1.5.14 (the beta version, but there have been no changes in this area) using wxWidgets 3.1.1 (older versions, 1.4.70/1 may have been compiled with wxWidgets 3.0.2 or earlier) and I don't see the issue. What vector chart are you using? CM93, s63,...? What version of wxWidgets are you using?

I have had issues with tearing of OCPN when using OpenGL on some devices, i.e. Raspberry PI, and issues running under VirtualBox, but they have not been specific to OD. It happens regardless of OD, just OD 'can' make it more obvious as the system is having to work harder.

Can you try with OD 1.4.4?

Thanks
Jon

I check on the version of CPN and the plugin from the site.
cards CM-93, ENC S-57
on beta 1.5. same thing

I think it's not in the plugin but in the CPN itself
I've already reported to Dave about the same problem with the card when the track highlight in OpenGL mode

[marathon lady]

Thanks for your help in the past some further notes on my progress.

I am trying to draw the no fishing zones on the NE coast of Australia. The coast is divided up into 19 zones (maps 1 to 19) each zone has a number of areas. Drawing these areas can use from 4 to over 200 Draw points.
Once I have completed each Area I name it and the draw points and save it to a folder.
During this process I have noticed the following
1. Open CPN shows an error (see below)
a. every time on shut down since I have loaded Draw.
b. when I try to delete groups of files (7 or more) from Draw Manager.


Message “opencpn.exe has stopped working. A problem caused the program to stop working correctly. Windows will close the program and notify you if a solution is available.”
2.When I exit out of CPN and return I have lost some of the titles to the areas it is replaced with (Unnamed) Boundary. 21 Titles are unchanged.
I am running windows 10 and the version 4.8.4 of Open CPN and Draw1.4.71

Russell

[marathon lady]

Update on the above problems. I deleted the ODnavobj.xml file and the problem with the error message has stopped, I am now reloading the areas I had created (from backup file) one at a time to see if the problem returns.

Russell

[jongough]

Hi Russell,
Can you attach a copy of your ODnavobj.xml so that I can have a look at what is happening?


Thanks
Jon

[marathon lady]

Sorry I deleted it an are unable to restore it, I will continue to load the areas in one at a time to see if I can cause the error
Russell

[marathon lady]

OK have the error again can you advise how I attach the file
Russell

[rgleason]

Russell, how big is it? If it is small enough, just add ".doc" or ".pdf"


When you attach there is a list of sizes for file types


http://www.cruisersforum.com/forums/...26e3463024b7d0

[marathon lady]

Thanks for the response the file is 650K the system will not let me load it message invalid file type.
Russell

[Dsanduril]

Russell,

1. Compress/Zip the file (Win10 right-click, Send To, Compressed (zipped) folder). That should drastically reduce the size of an xml file.

2. Rename the file (Win10 right-click, rename OR F2), changing the extension from '.zip' to '.pdf' (Windows will complain about this, tell it you really want to). That will make the system here think it is a valid type.

Post the file, and let everyone know it is a zip file, when they download it they can reverse your steps.

[marathon lady]

Sorry for the delay but computer are still a mystery to me. I hope I have done this right the attached file is a zipped file with a name change to allow me to attached to this message.
I deleted all the areas I created and started to add them back until the error message (program stopped) appeared.
Russell

[rgleason]

Updated version for windows of Jon's new 1.5


https://github.com/rgleason/ocpn_dra...ag/v1.5.22beta

[Gilletarom]

Hello JonGough, Hello RGleason,

Originally Posted by rgleason

Updated version for windows of Jon's new 1.5
https://github.com/rgleason/ocpn_dra...ag/v1.5.22beta

With my Laptop Lenovo, W 10.

I have a 4.84 version and a 4.86 version in parallel.
- On version 4.84, I use DR 1.4.47. No problem.
- On version 4.86, I tried to install version 1.5.22 given now online on the OpenCPN.org website. But, this version of DR does not appear in the list of plugins in "Options / Plugins" tab.

What about ?



Gilletarom.

[bcn]

I think you need the 4.99 for the beta.

[Gilletarom]

Hello Hubert,

Originally Posted by bcn

I think you need the 4.99 for the beta.

Hum ... If that's true, why is this version online on OpenCPN.org for O486?


Gilletarom.