Cruisers Forum
 

Go Back   Cruisers & Sailing Forums > Search Forums
Reload this Page Search Results
Cruiser Wiki Click Here to Login
Register Vendors FAQ Community Calendar Today's Posts Log in

Page 1 of 20 1 2311 Last »
Showing results 1 to 25 of 500
Search took 0.01 seconds. Search: Posts Made By: shakey doug
Forum: Engines and Propulsion Systems 01-12-2019, 21:30
Replies: 124
Views: 27,768
Posted By shakey doug
Re: Adding Used Motor Oil to Diesel Fuel?

As a 17yr old apprentice diesel fitter I had to watch a series of films on the properties of various lube oils and motive fuels, including the use of sump oil reuse. Having seen used oil magnified...
Forum: Engines and Propulsion Systems 28-11-2019, 23:50
Replies: 17
Views: 11,978
Posted By shakey doug
Re: Perkins M30 is this motor legitimate?

Make contact with The Rock Tractor Centre, the Rock NSW, with your newly acquired knowledge. These people have Australia's foremost Perkins knowledge.
Forum: Engines and Propulsion Systems 11-10-2019, 01:04
Replies: 42
Views: 39,812
Posted By shakey doug
Re: WARNING Do Not Buy Nanni Diesel in USA!

A lot of marinized auto & Ag engines have heavier flywheels hence starter differences.
Forum: Engines and Propulsion Systems 16-09-2019, 02:04
Replies: 17
Views: 2,245
Posted By shakey doug
Re: Engine shuts down when put in forward or reverse

Are you able to vary rpms in neutral?
Forum: Engines and Propulsion Systems 08-08-2019, 19:44
Replies: 21
Views: 3,394
Posted By shakey doug
Re: Help!! Perkins4-108/Westerbeke wont bleed

Have you cleaned filter under lid of lift pump? A good strong dribble is enough for a start if no air is present.
Forum: Engines and Propulsion Systems 03-08-2019, 01:33
Replies: 30
Views: 3,969
Posted By shakey doug
Re: 47'Perry needs a new heart

Many parts available in OZ for Ford 80hp 2712e. Including Lehman conversion, what has happened?
Forum: Engines and Propulsion Systems 19-03-2019, 14:58
Replies: 15
Views: 1,460
Posted By shakey doug
Re: Running Hotter Now

Raw or fresh water cooled??
Forum: Engines and Propulsion Systems 12-03-2019, 03:06
Replies: 12
Views: 2,195
Posted By shakey doug
Re: Getting a good used engine in Australia?

A quick scan of Gumtree turned up a few.
Forum: Engines and Propulsion Systems 12-03-2019, 02:59
Replies: 12
Views: 2,195
Posted By shakey doug
Re: Getting a good used engine in Australia?

Where in aust are you??
Forum: Engines and Propulsion Systems 25-02-2019, 14:01
Replies: 13
Views: 2,067
Posted By shakey doug
Re: Yanmar Seawater Pump Failure When Sailing

Quickest, Cheapest and Easiest things first.
Forum: Engines and Propulsion Systems 25-02-2019, 00:33
Replies: 13
Views: 2,067
Posted By shakey doug
Re: Yanmar Seawater Pump Failure When Sailing

Pump face plate or cam worn, try turning face plate over.
Forum: Engines and Propulsion Systems 15-02-2019, 14:40
Replies: 48
Views: 19,768
Posted By shakey doug
Re: Smoking rebuilt Perkins Diesel help needed!!!

Old copper injector seal joint can be left in bottom of hole, new joint fitted to replacement injector then fitted= 2 joints in place = white/ grey smoke.
Forum: Engines and Propulsion Systems 07-02-2019, 22:52
Replies: 21
Views: 6,125
Posted By shakey doug
Re: Beta 38 vs 35 RPM

Just a thought, but could the 3,600 rpm unit be for fitment to a 2 pole 60hz Generator?
Forum: Engines and Propulsion Systems 04-01-2019, 20:20
Replies: 15
Views: 6,530
Posted By shakey doug
Re: Volvo Penta MD2030-D Faulty Injection Pump?

Rig up a separate clean fuel supply direct to the injection pump with 6 to 8ft head on it this will eliminate a lot of may be -- could be's.
Forum: Engines and Propulsion Systems 23-12-2018, 21:13
Replies: 95
Views: 10,825
Posted By shakey doug
Re: heavy displacement repower dilemma

Perkins HT 6354. [Horizontal]
Forum: Engines and Propulsion Systems 19-12-2018, 13:39
Replies: 50
Views: 5,906
Posted By shakey doug
Re: Letting Oil Drain Out for a week

Priming can become an issue if any oil pump wear is present.
Forum: Engines and Propulsion Systems 23-11-2018, 03:21
Replies: 22
Views: 9,104
Posted By shakey doug
Re: Fuel leaking into the sea from my exhaust

Just noted 3cyl engine involved undo each fuel feed line at injector note least reaction cyl this will be the crook one.
Forum: Engines and Propulsion Systems 23-11-2018, 02:35
Replies: 22
Views: 9,104
Posted By shakey doug
Re: Fuel leaking into the sea from my exhaust

Do the cheap & easy things first do not be pressured into a partial or full pull down at this point. 1. Remove both injectors loosen turn towards a clear space observe spray mist and listen for...
Forum: Engines and Propulsion Systems 15-11-2018, 14:51
Replies: 131
Views: 65,284
Posted By shakey doug
Re: Seized Injectors - Need Ideas to Remove!

I have sent you a message
Forum: Engines and Propulsion Systems 15-11-2018, 14:28
Replies: 131
Views: 65,284
Posted By shakey doug
Re: Seized Injectors - Need Ideas to Remove!

where abouts in Tassie are you?
Forum: Engines and Propulsion Systems 15-11-2018, 14:03
Replies: 131
Views: 65,284
Posted By shakey doug
Re: Seized Injectors - Need Ideas to Remove!

Not suggesting you bash hell out of the chamber but give the nozzle holder body a touch up.
Forum: Engines and Propulsion Systems 15-11-2018, 13:35
Replies: 131
Views: 65,284
Posted By shakey doug
Re: Seized Injectors - Need Ideas to Remove!

Photo #3. This is not part of the injector but the combustion anti chamber [ Lombardo chamber] this motor has indirect injection.
6''x1'' brass stock and a minimum 5 pound maul or larger and...
Forum: Engines and Propulsion Systems 15-11-2018, 00:00
Replies: 19
Views: 10,662
Posted By shakey doug
Re: Velvet Drive leakage

My reply should have been presented clearer. Early 70 series splines require a non hardening sealant, later units came dry from the factory. The same sealant should also be used on the seal to casing...
Forum: Engines and Propulsion Systems 14-11-2018, 18:42
Replies: 19
Views: 10,662
Posted By shakey doug
Re: Velvet Drive leakage

Lip seal only, socket size 1.11/16''. Check seal running area for any marking, may require sleeving or metal spray.
Forum: Engines and Propulsion Systems 23-10-2018, 01:53
Replies: 14
Views: 3,094
Posted By shakey doug
Re: sqealing noise

Singing Prop??
Showing results 1 to 25 of 500
Page 1 of 20 1 2311 Last »

 
Forum Jump


All times are GMT -7. The time now is 21:04.

Contact Us - Cruisers & Sailing Forums - Sitemap - Community Rules - Terms of Service - Privacy - Accessibility - Top

Google+
Powered by vBulletin® Version 3.8.8 Beta 1
Copyright ©2000 - 2024, vBulletin Solutions, Inc.
Social Knowledge Networks
Powered by vBulletin® Version 3.8.8 Beta 1
Copyright ©2000 - 2024, vBulletin Solutions, Inc.
close

Privacy Guaranteed - your email is never shared with anyone, opt out any time.


ShowCase vBulletin Plugins by Drive Thru Online, Inc.