Cruisers Forum
 


Join CruisersForum Today

Reply
 
Thread Tools Rate Thread Display Modes
Old 20-02-2012, 19:11   #1
Registered User
 
MylesK1's Avatar

Join Date: Dec 2010
Location: NYC
Boat: Lagoon 440 (44'8")
Posts: 54
Changing Table Tops

OK, I feel like an idiot, but I've got to ask...

To change the table tops, do i remove all of the screws from the mounts from the under-side of the table-tops?

Please don't laugh. I just need some advice on what's probably the obvious.

Thanks!

__________________

__________________
MylesK1 is offline   Reply With Quote
Old 20-02-2012, 23:34   #2
Registered User
 
PaulinOz's Avatar

Join Date: Jan 2011
Location: East Coast Australia on board L450
Boat: Lagoon 421(2010) & L450(2013)
Posts: 723
Images: 17
Re: Changing Table Tops

The Aluminum legs just push into the deck and push into the underside of Table on my 421 first time I moved them the where very tight cleaned the surfaces and lubricated with a small wipe of CRC and remove/insert easy now.
__________________

__________________
PaulinOz is online now   Reply With Quote
Old 21-02-2012, 05:32   #3
Registered User
 
MylesK1's Avatar

Join Date: Dec 2010
Location: NYC
Boat: Lagoon 440 (44'8")
Posts: 54
Re: Changing Table Tops

Hmm... tried pushing it down and pulling it up but no luck. I tried spinning the legs but they wouldn't budge.

Not sure how these detach. Ugh.
__________________
MylesK1 is offline   Reply With Quote
Old 23-02-2012, 04:28   #4
Registered User

Join Date: Sep 2010
Location: Amsterdam
Boat: Lagoon 500
Posts: 21
Images: 1
Re: Changing Table Tops

Hi Myles,

had same problem, believe me .. they wil come loose in the end, what really helped was gently hitting the top of the mounts with a hammer , the vibrations will free it.

while you're at it...get a nice square teak table....the difference is amazing :-)

regards patrick
__________________
"Blessed are they who can laugh at themselves, for they shall never cease to be amused..."
Poco Loco III is offline   Reply With Quote
Old 23-02-2012, 05:00   #5
Registered User
 
MylesK1's Avatar

Join Date: Dec 2010
Location: NYC
Boat: Lagoon 440 (44'8")
Posts: 54
Re: Changing Table Tops

Thanks, Patrick. I'm going to get some WD-40 and a rubber mallet and see what shakes loose.
__________________
MylesK1 is offline   Reply With Quote
Old 23-02-2012, 05:34   #6
Registered User
 
dirkdig's Avatar

Join Date: Oct 2007
Location: Geelong,Australia
Boat: Lagoon 440 Pathfinder
Posts: 838
Had to use big plumbers grips around the pipe to get ours loose, once done i keep them now with a bit of grease.
__________________

__________________
dirkdig is offline   Reply With Quote
Reply

Thread Tools
Display Modes Rate This Thread
Rate This Thread:

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off
Trackbacks are Off
Pingbacks are Off
Refbacks are Off


Similar Threads
Thread Thread Starter Forum Replies Last Post
Protocol for Changing Fuel Filter Knowazark Engines and Propulsion Systems 3 31-01-2012 18:46
Changing My Rigging One Stay at a Time Solo Hazard808 Deck hardware: Rigging, Sails & Hoisting 20 08-01-2012 09:23
changing mast monet Monohull Sailboats 3 31-12-2011 17:38
Changing Marine Gear Lube Oil on Yanmar 4JH msulc Engines and Propulsion Systems 3 30-12-2011 18:14



Copyright 2002- Social Knowledge, LLC All Rights Reserved.

All times are GMT -7. The time now is 23:51.


Google+
Powered by vBulletin® Version 3.8.8 Beta 1
Copyright ©2000 - 2017, vBulletin Solutions, Inc.
Social Knowledge Networks
Powered by vBulletin® Version 3.8.8 Beta 1
Copyright ©2000 - 2017, vBulletin Solutions, Inc.

ShowCase vBulletin Plugins by Drive Thru Online, Inc.