|
|
17-10-2009, 08:19
|
#16
|
Registered User
Join Date: Oct 2009
Posts: 15
|
I watched the mechanic hone the bore and fit the rings. We both checked they are right way up, properly orientated, and checked the ring gap with a feeler gauge. Old rings looked good too, and remember problem was there before we stripped. My background was as a car mechanic so I know what is involved. Compression gauge is from my car dealership and has always been reliable. Engine always starts first touch and sounds very good on idle with clean exhaust. Problem begins at 3/4 throttle in neutral and at about 1/2 throttle when in gear. Prop is unchanged in 11 years I have the boat. We have been testing with air filter removed, so that is not an issue.
Bill.
|
|
|
17-10-2009, 09:21
|
#17
|
Registered User
Join Date: Mar 2003
Location: Philippines in the winters
Boat: It’s in French Polynesia now
Posts: 11,369
|
Last Resort
Try changing the fuel or at least run in a secondary line from a portable can. Black smoke usually indicates too much fuel or a bad mix.
__________________
Faithful are the Wounds of a Friend, but the Kisses of the Enemy are Deceitful! ........
The measure of a man is how he navigates to a proper shore in the midst of a storm!
|
|
|
17-10-2009, 09:41
|
#18
|
Sponsoring Vendor
Join Date: Oct 2007
Location: Hollywood, Fl.
Boat: FP Athena 38' Poerava
Posts: 3,984
|
Quote:
Originally Posted by billmcc
I watched the mechanic hone the bore and fit the rings. We both checked they are right way up, properly orientated, and checked the ring gap with a feeler gauge. Old rings looked good too, and remember problem was there before we stripped. My background was as a car mechanic so I know what is involved. Compression gauge is from my car dealership and has always been reliable. Engine always starts first touch and sounds very good on idle with clean exhaust. Problem begins at 3/4 throttle in neutral and at about 1/2 throttle when in gear. Prop is unchanged in 11 years I have the boat. We have been testing with air filter removed, so that is not an issue.
Bill.
|
Process of elimination as you know and I'm just throwing different things out. I assume this is a recent problem and the engine worked well before? We can pretty much eliminate the top of the engine for obvious reasons. That takes care of valves, stems, cracked head etc. You're sure there is no exhaust blockage. So looking below that point would seem rather obvious. As you know compression testers for gas engines are different from diesel engines. If you're getting a true 40bar or 580psi reading that could be indicative of something as I believe the rated pressures are below that by about 100psi. Piston head is clean? Did you mic the cylinder and piston after honing for eccentric and circularity wear ? If all these checked out I'd still suspect fuel delivery. A defective fuel injection pump or incorrect fuel injection timing as others have stated. Have you changed fuel filters and run a different source of known new and clean fuel? One other wrench in the mix. You said you changed the alternator. What is the amp rating?
|
|
|
17-10-2009, 09:52
|
#19
|
Registered User
Join Date: Mar 2003
Location: Philippines in the winters
Boat: It’s in French Polynesia now
Posts: 11,369
|
Quote:
Originally Posted by Tellie
You said you changed the alternator. What is the amp rating?
|
Good thought!
Try pulling the belt off the alternator or disconnect the wires and test run. An overload can cause these symptoms.
__________________
Faithful are the Wounds of a Friend, but the Kisses of the Enemy are Deceitful! ........
The measure of a man is how he navigates to a proper shore in the midst of a storm!
|
|
|
17-10-2009, 10:34
|
#20
|
Registered User
Join Date: Oct 2005
Location: Cruising NC, FL, Bahamas, TCI & VIs
Boat: 1964 Pearson Ariel 'Faith' / Pearson 424, sv Emerald Tide
Posts: 1,531
|
Quote:
Originally Posted by delmarrey
Good thought!
Try pulling the belt off the alternator or disconnect the wires and test run. An overload can cause these symptoms.
|
From the original post;
Quote:
My engine throws out clouds of black smoke and oil under any kind of load and I can only get 2.5Kts (plus 1 Kt if alternator belt disconnected) instead of my customary 5Kts.
|
|
|
|
17-10-2009, 11:10
|
#21
|
Eternal Member
Join Date: Aug 2006
Location: North of Baltimore
Boat: Ericson 27 & 18' Herrmann Catboat
Posts: 3,798
|
This one has me scratching my head on this blustery day on the Chesapeake.
Just a thought...with the engine in neutral and OFF...can you turn the shaft from the inside easily?
I am just trying to rule out "load" issues.
|
|
|
17-10-2009, 11:38
|
#22
|
Registered User
Join Date: Oct 2005
Location: Cruising NC, FL, Bahamas, TCI & VIs
Boat: 1964 Pearson Ariel 'Faith' / Pearson 424, sv Emerald Tide
Posts: 1,531
|
Quote:
Originally Posted by Chief Engineer
This one has me scratching my head on this blustery day on the Chesapeake.
Just a thought...with the engine in neutral and OFF...can you turn the shaft from the inside easily?
I am just trying to rule out "load" issues.
|
I thought about that too, seems like they checked this with this statement;
Quote:
Prop and gearbox not producing extra drag
|
I don't know how they would determine this other then checking the prop for growth and checking the resistance to turning by hand....
But if those things were not done (not sure what else that statement would mean) they certainly need to check.
This kind of suggests that it is not a load problem also;
Quote:
Problem begins at 3/4 throttle in neutral and at about 1/2 throttle when in gear.
|
|
|
|
17-10-2009, 11:41
|
#23
|
Registered User
Join Date: Oct 2005
Location: Cruising NC, FL, Bahamas, TCI & VIs
Boat: 1964 Pearson Ariel 'Faith' / Pearson 424, sv Emerald Tide
Posts: 1,531
|
Quote:
Originally Posted by Tellie
Process of elimination as you know and I'm just throwing different things out. I assume this is a recent problem and the engine worked well before? ......
|
I think he answered this back in post #14
Quote:
Faith: Original presenting problem was 'smoke, no power' and occurred a week after I fitted a new alternator...
|
|
|
|
17-10-2009, 11:50
|
#24
|
Sponsoring Vendor
Join Date: Oct 2007
Location: Hollywood, Fl.
Boat: FP Athena 38' Poerava
Posts: 3,984
|
Quote:
Originally Posted by s/v 'Faith'
I think he answered this back in post #14
|
Should we start taking wagers?
Even though they have been checked and of course not being there, I guess fuel pump or blocked exhaust.
|
|
|
17-10-2009, 13:29
|
#25
|
Registered User
Join Date: Oct 2009
Posts: 15
|
Tellie: Tank cleaned, fresh fuel and filters start of season (April) but will try fresh direct feed as you suggest. Drew off fuel via injector pump bleed screw - left to stand in jar and looks clean and pure.
Did not mic bore. Very light honing and inserted comp. ring in worn area and checked ring gap with feeler gauge. Bore looks good with no lip. Piston head cleaned. Compression test and slow cylinder leakage surely indicates good tight piston & rings. My gauge is designed for diesel engines. Can't see how I could have "too much compression" as engine starts so easily by hand or by starter.
Alternator is generic (190 euro v.Yanmar one at over 400!). It could be wrong amperage but all testing has been done with belt off as well as on.
Chief: Have turned engine (on half compression) with starting handle both in and out of gear to rule out excessive gearbox, shaft or prop load. My mechanic called Yanmar in the UK - they suggested excessive load, but I think I have ruled it out at this stage. Previously they were "certain" we would find a blocked exhaust....but no!
Wife says I should buy a new engine, but I said if I did I would spend the rest of my life wondering what the hell was wrong with the old one! I am not going to let this beat me!
|
|
|
17-10-2009, 13:38
|
#26
|
Registered User
Join Date: Oct 2005
Location: Cruising NC, FL, Bahamas, TCI & VIs
Boat: 1964 Pearson Ariel 'Faith' / Pearson 424, sv Emerald Tide
Posts: 1,531
|
Ah....
Quote:
Have turned engine (on half compression) with starting handle both in and out of gear to rule out excessive gearbox, shaft or prop load. My mechanic called Yanmar in the UK - they suggested excessive load, but I think I have ruled it out at this stage.
|
Have you dove on the prop? I know it would not affect the problem at "3/4 throttle in neutral" but a bent blade or a fouled prop WILL cause excessive loading and the exact symptoms you describe running in gear.
Good luck!
|
|
|
17-10-2009, 15:16
|
#27
|
Registered User
Join Date: Oct 2009
Posts: 15
|
Yes, I had a diver down to check prop as my first reaction, before I started work on the engine.
Bill.
|
|
|
17-10-2009, 15:30
|
#28
|
Eternal Member
Join Date: Aug 2006
Location: North of Baltimore
Boat: Ericson 27 & 18' Herrmann Catboat
Posts: 3,798
|
Going back to the original post......
What did you do to check exhaust?
There are a number of things that can cause back pressure.
Delaminated hose Hose can look fine on the outside but I have seen hoses that had "flaps" hanging off the inside.
Obstructed Exhaust elbow (When was the last time this was changed) They do have a lifespan in salt water.
Damaged Water lift muffler
|
|
|
17-10-2009, 15:41
|
#29
|
Registered User
Join Date: Oct 2005
Location: Cruising NC, FL, Bahamas, TCI & VIs
Boat: 1964 Pearson Ariel 'Faith' / Pearson 424, sv Emerald Tide
Posts: 1,531
|
Quote:
Originally Posted by billmcc
Yes, I had a diver down to check prop as my first reaction, before I started work on the engine.
Bill.
|
Bill,
No, you were SUPPOSED to say "Oh yea! Why did'nt I think of that!" and then report this fixed the problem..
Oh wait, the Chief has another idea... yea check that.
Good luck!
|
|
|
18-10-2009, 08:46
|
#30
|
Registered User
Join Date: Oct 2009
Posts: 15
|
Chief: We removed exhaust hoses, looked through them (about the only light at the end of the tunnel!) blew through them and hosed water through. Removed and washed out water trap. I am not sure about the elbow - it has never been changed. I will whip it off next week, and if in doubt will test with the elbow off my friend's boat. Blocked elbow would tick all the boxes! Will let you know how I get on. Thanks again.
Bill.
|
|
|
|
|
Thread Tools |
Search this Thread |
|
|
Display Modes |
Rate This Thread |
Linear Mode
|
|
Posting Rules
|
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts
HTML code is Off
|
|
|
|
Advertise Here
Recent Discussions |
|
|
|
|
|
|
|
|
|
|
|
|
Vendor Spotlight |
|
|
|
|
|