|
27-05-2013, 10:52
|
#1
|
Senior Cruiser
Join Date: Aug 2009
Posts: 4,033
|
Outboard Shaft Length?
I am getting a new outboard . . . to be used on a 3m (10') normal avon inflatable (With inflatable floor). Simple question - what shaft length do I want - 15" or 20"
The transom is 41cm (16") from top to bottom .
Our current outboard we bought in Iceland, and is metric measurements and looks to have a 45cm shaft = 18"
|
|
|
27-05-2013, 11:19
|
#2
|
Registered User
Join Date: Oct 2005
Location: Cruising NC, FL, Bahamas, TCI & VIs
Boat: 1964 Pearson Ariel 'Faith' / Pearson 424, sv Emerald Tide
Posts: 1,531
|
Re: outboard shaft length?
Short shaft nominally 15" from prop shaft to transom mount, is generally the length for a dingy motor.
|
|
|
27-05-2013, 12:20
|
#3
|
Moderator
Join Date: Nov 2011
Location: aboard, in Tasmania, Australia
Boat: Sayer 46' Solent rig sloop
Posts: 28,669
|
Re: outboard shaft length?
Evans, you don't mention the hp of the engine, but I'd be inclined towards the "short shaft". My concern is that the inflatable floors are not really very rigid, and the torque on the boat generated by a long shaft would be more likely to bend the floor in use, compared to the short shaft where the lever arm is shorter. Or am I purely wrong in this assumption?
Ann
__________________
Who scorns the calm has forgotten the storm.
|
|
|
27-05-2013, 12:57
|
#4
|
Registered User
Join Date: Oct 2005
Location: Presently on US East Coast
Boat: Manta 40 "Reach"
Posts: 10,108
|
Re: outboard shaft length?
You want the cavitation plate to be 3-4" under water when the boat is at rest with the engine installed. Generally, this will place the cavitation plate 0-2" below the bottom of the dinghy hull.
The shaft length is measured from the clamp where it rests on the top of the transom to the cavitation plate.
Does Avon recommend a shaft length? If not, I'm thinking the 15" will work.
Mark
__________________
www.svreach.com
You do not need a parachute to skydive. You only need a parachute to skydive twice.
|
|
|
27-05-2013, 13:02
|
#5
|
Senior Cruiser
Join Date: Aug 2009
Posts: 4,033
|
Re: outboard shaft length?
ok, great. Thanks guys (and gal) I got a 15".
Ann, 6hp . . . pretty small by modern standard, but we can plane with both of us in the dinghy (if it's dry).
|
|
|
27-05-2013, 14:34
|
#6
|
Nearly an old salt
Join Date: Jun 2009
Location: Lefkas Marina ,Greece
Boat: Bavaria 36
Posts: 22,801
|
Re: outboard shaft length?
whatever you get the cavitation plate should just be at or just below the lowest point of the transom.
dave
__________________
Interested in smart boat technology, networking and all things tech
|
|
|
27-05-2013, 15:07
|
#7
|
Registered User
Join Date: May 2008
Location: British Columbia, Mexico
Boat: S&S Hughes 38
Posts: 837
|
Re: Outboard Shaft Length?
If your transom is 16" how is a 15"shaft going to work?I bought a short shaft Suzuki 4hp,4stroke thinking it would fit my 8ft. inflatable.Had to cut the transom 1.5 in. so it wouldn't cavitate.
|
|
|
28-05-2013, 20:38
|
#8
|
Registered User
Join Date: Oct 2007
Location: On the boat
Boat: Valiant 50
Posts: 509
|
Re: Outboard Shaft Length?
This begs the question.. can a shaft on a modest HP outboard be too long? And would it not be better to err on the long side of ideal?
We have a 5HP Yamaha with long shaft (this was all that was available on the day) which drives our 8ft soft floor dinghy. Seems to work ok, but we can only plane with one on board, sitting as far forward as possible - I put this down to the drag of the soft slatted floor.
__________________
The light at the end of the tunnel are no longer the headlights of the oncoming train......yippee
|
|
|
28-05-2013, 22:17
|
#9
|
Registered User
Join Date: Dec 2009
Posts: 2,959
|
Long shafts are nice because the prop is less apt to suck air at high power, in chop, whatever, without the extra extended fins.
Not so nice in shallow coral and rock.
Cavitation plate should be somewhat below the bottom edge of the transom.
|
|
|
|
Thread Tools |
Search this Thread |
|
|
Display Modes |
Rate This Thread |
Linear Mode
|
|
Posting Rules
|
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts
HTML code is Off
|
|
|
|
Advertise Here
Recent Discussions |
|
|
|
|
|
|
|
|
|
|
|
|
Vendor Spotlight |
|
|
|
|
|