|
17-06-2010, 15:29
|
#1
|
Registered User
Join Date: May 2009
Location: Grenada
Boat: Shorebro,Royal 33 - Aloisius
Posts: 1,059
|
Chain Covered with Barnacles and Algae
I raised my chain today and it is covered with growth, barnacles and algae. Does anyone have an idea of a way to clean it. It is galvanized and I am thinking of a couple of methods
using muriatic acid and then a brush with lots of water but I am afraid it will affect the galvanizing.
using Clorox then a brush and lots of water
dragging it in a rocky parking lot behind my car
running it up and down in the water from my boat with a scrubber attached
Any suggestions?
|
|
|
17-06-2010, 15:35
|
#2
|
CF Adviser
Join Date: Dec 2008
Location: sausalito
Boat: 14 meter sloop
Posts: 7,260
|
is a pressure washer a possibility?
__________________
cruising is entirely about showing up--in boat shoes.
|
|
|
17-06-2010, 16:04
|
#3
|
Registered User
Join Date: May 2009
Location: Grenada
Boat: Shorebro,Royal 33 - Aloisius
Posts: 1,059
|
Pressure washer is not possible
|
|
|
17-06-2010, 16:27
|
#4
|
Registered User
Join Date: Sep 2009
Location: On the Gorge waterway in the heart of Victoria, British Columbia.
Boat: Explorer 44 by Stan Huntingford. Building in progress.
Posts: 30
|
I think for barnacles the only option is a pressure washer. If my memory is still holding up?? you will need a machine with a minimum of at least 3400 PSI for barnacles. If you are thinking of dragging the chain over a parking lot, don't. You will wear off the galvanizing in short order. Instead, take it to a pressure washer.
BJB
|
|
|
17-06-2010, 16:46
|
#5
|
Registered User
Join Date: May 2009
Location: Grenada
Boat: Shorebro,Royal 33 - Aloisius
Posts: 1,059
|
I use muriatic acid on my dinghy to get rid of barnacles, would this hurt the galvanized chain? Then use a brush and rinse with a lot of water.
|
|
|
17-06-2010, 17:42
|
#6
|
Senior Cruiser
Join Date: May 2008
Location: near Annapolis
Boat: PDQ 36 & Atlantic 42
Posts: 1,178
|
Muriatic acid is the trick. It's commonly used in swimming pool maintenance and is relatively inexpensive. It dissolves the calcium in the barnacle shell and rinses clean with water. Mary Kate On-Off blends three acids to do the same thing but gets expensive in the quantity needed. Find a plastic drum or barrel big enough to hold the chain, pour as much muriatic acid as you can get over it and soak the chain thoroughly. Absolutely avoid contact; wear gloves and face protection, you won't have to be told twice to not breath the fumes. Don't dump it anywhere it can pollute living waters, but you can rinse it off and almost all the grown with a stiff brush and a hose.
I use it in a garden sprayer to get the barnacles out of hard to reach places like the top of my rudders.
|
|
|
17-06-2010, 18:19
|
#7
|
Writing Full-Time Since 2014
Join Date: Nov 2008
Location: Deale, MD
Boat: PDQ Altair, 32/34
Posts: 9,630
|
Quote:
Originally Posted by sandy daugherty
Muriatic acid is the trick. It's commonly used in swimming pool maintenance and is relatively inexpensive. It dissolves the calcium in the barnacle shell and rinses clean with water. Mary Kate On-Off blends three acids to do the same thing but gets expensive in the quantity needed. Find a plastic drum or barrel big enough to hold the chain, pour as much muriatic acid as you can get over it and soak the chain thoroughly. Absolutely avoid contact; wear gloves and face protection, you won't have to be told twice to not breath the fumes. Don't dump it anywhere it can pollute living waters, but you can rinse it off and almost all the grown with a stiff brush and a hose.
I use it in a garden sprayer to get the barnacles out of hard to reach places like the top of my rudders.
|
...but don't leave it for too long. The acid is eating the zinc too. Just long enough to get the barnacles to let go. Then power wash.
|
|
|
17-06-2010, 19:59
|
#8
|
Registered User
Join Date: Jun 2010
Location: Mexico (currently)
Boat: Panda 40 - S/V Cambria
Posts: 573
|
Remove the chain and dip in HCl then powerwash every time you raise the anchor? Don't think so...
The growth is usually on the chain in the water column, the bit of ocean between your hull and the bottom. The stuff along the bottom stays relatively clean, it's getting polished by the sediment. When I know I will be leaving soon, I drop that much chain into the water the day before so that the original length between boat and bottom is now on the bottom, getting scrubbed. If I don't have that much time, it's into the water with a nylon scrub brush, a thin drywall spatula, and a putty knife to scrub the grass and soft stuff off, then pop the barnacles. The little barnacle bottoms are still on until the next time the chain sits on the bottom for a while, but it doesn't smell in a hot chain locker. (It helps to have a power windlass with a control on a wire to advance the chain while in the water scrubbing, otherwise someone pulling in a few feet at a time.)
Michael
|
|
|
30-09-2010, 02:12
|
#9
|
Registered User
Join Date: Sep 2010
Location: Paradise (better known to most people as: Philippines)
Boat: 65' Custom Steel Ketch
Posts: 322
|
Quote:
Originally Posted by svcambria
When I know I will be leaving soon, I drop that much chain into the water the day before so that the original length between boat and bottom is now on the bottom, getting scrubbed. If I don't have that much time, it's into the water with a nylon scrub brush, a thin drywall spatula, and a putty knife to scrub the grass and soft stuff off, then pop the barnacles.
Michael
|
That's how I do it. My chain gets so scuzzy where I anchor, I can get 90% of it with a leather glove up and down the nasty part.
Yes, it's somewhat degrading to do, but it works.
|
|
|
30-09-2010, 04:07
|
#10
|
Moderator Emeritus
Join Date: Jul 2010
Location: Key West & Sarasota
Boat: Cal 28 "Happy Days"
Posts: 4,210
|
The zinc galvanizing will come off pretty fast in acid... Think battery! Dissimilar metals Zinc & steel) in an electrolyte (acid). Before the flames start, yes I know a chain in a bucket of acid is NOT going to produce electricity.
I would put the chain in a barrel, put on the lid and tumble it....
__________________
Any fool with a big enough checkbook can BUY a boat; it takes a SPECIAL type of fool to build his own! -Capngeo
|
|
|
30-09-2010, 06:38
|
#11
|
Registered User
Join Date: Oct 2009
Posts: 764
|
Quote:
Originally Posted by capngeo
The zinc galvanizing will come off pretty fast in acid... ....
|
ditto that. Once upon a time I used muric acid to remove rust from my chain. It came out like new but as it dried a surface layer of rust appeared. I tired to spray coat it with galvanizing spray and was disappointed in the results. Hot dipped galvanizing was the way to go, but did not have the necessary set up to do. So if you try the acid be aware that the galvanizing will probably be affected.
|
|
|
30-09-2010, 15:28
|
#12
|
Registered User
Join Date: May 2009
Location: Grenada
Boat: Shorebro,Royal 33 - Aloisius
Posts: 1,059
|
Yes the acid will eat at the galvanizing. It has but not too bad. Next time I will let out different lenghts so that it naturally gets sanded on the bottom. If it is out to long and gets crusty, I think I will try turning the chain around and have the crusty area down by the anchor being cleaned on the bottom naturally rather than using acid.
|
|
|
|
Thread Tools |
Search this Thread |
|
|
Display Modes |
Rate This Thread |
Linear Mode
|
|
Posting Rules
|
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts
HTML code is Off
|
|
|
|
Advertise Here
Recent Discussions |
|
|
|
|
|
|
|
|
|
|
|
|
Vendor Spotlight |
|
|
|
|
|