Cruisers Forum
 

Go Back   Cruisers & Sailing Forums > Cruising Business & Commerce > General Classifieds (no boats) > Classifieds Archive
Cruiser Wiki Click Here to Login
Register Vendors FAQ Community Calendar Today's Posts Log in

 
 
Thread Tools Search this Thread Rate Thread Display Modes
Old 13-01-2013, 17:10   #1
Registered User

Join Date: Sep 2011
Location: East Hampton, CT
Boat: Maine Cat 30
Posts: 29
Precision Temp Showermate M-550S Hot Water Heater

I have this hot water heater minimaly used. This is a Propane Instant hot water heater. This was pulled off a boat that entered charter due to Coast Guard regs. Below are the specs off of the manufacturer's website. Pm me if your interested, I'll take 800 for it, plus shipping. It goes for 1500 new.





Type: Gas instantaneous, power vented. Full gas modulation temperature control.
Dimensions: 11.5″ Wide x 13.5″ Deep x 19″ High, including power vent.
Weight: 30.5 pounds full.
Hook-ups: Electric: 18-2 x 2′ lead.Gas: Brass 3/8″ flare inside case, rear accessible.
Water: 1/2″ OD copper tubing.

Brass compression to 1/2″ NPT elbow can be installed or as specified.

Capacity: 55,000 Btu input – 44,000 Btu output at maximum burn at 8.5 WCI manifold pressure.15,000 Btu input – 10,600 Btu output at low burn at 1.2 WCI manifold pressure.
(88°F temperature rise per gallon per minute continuous flow at high burn).

Fuel Consumption: 2.55 lbs per hour at maximum input.(At 2 GPM of water, 20 lbs of propane will produce over 940 gallons of hot water).
Mounting: Side-mounted keyed bracket. Left or right side mounted.
Clearances: Zero clearance top (blower), bottom and sides. 2″ in back for hook-ups. Enough space in front to remove cover for service.
Venting: 2” power vent with proofing switch. (2” stainless flex duct recommended to the outside and can
run up to 15&prime.
Construction: Modular: Three assemblies; gas, electronics and water.Burner: High primary air, 12 element, atmospheric type.
Aluminized steel body with stainless flame strips.

Heat exchanger: Copper fin tube type with wrap for cooling.

Electronics: Plug in, potted, works-in-a-drawer.

Case and flue assembly are stainless steel.

Fuel: Propane at 11 WCI
Power: Burner: 12 element high primary air, atmospheric type with stainless steel flame strips.Aluminum manifold with brass pressure tap.
Orifices: Brass # 71 x 12.Gas Valve: Redundant solenoid with integral regulator

Water Temperature: Factory set at 115° F. Can be field adjusted 90° to 135°F.
Mounting:
Mounting flanges included. Must be mounted in accordance with any applicable Coast Guard and ABYC recommendations.
Safety Features: The Shower-Mate is pilotless. There is no flame unless water flow is sensed.Flame rectification: Gas valve shuts off in .8 of a second if there is a flame outage.
Redundant gas solenoid.

Electronic high temperature shut-off (2).

ECO high temperature shut off @ 165°F with manual reset.Pressure relief valve at 100 PSI.

Power vent must proof fluing before gas valve opens.
JRMarine is offline  
Old 13-07-2013, 08:00   #2
Registered User

Join Date: Jul 2013
Posts: 9
Re: Precision Temp Showermate M-550S Hot Water Heater

Good day,

Do you still have this water heater for sale?

Tim
SVMargarita is offline  
 


Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off
Trackbacks are Off
Pingbacks are Off
Refbacks are Off


Advertise Here


All times are GMT -7. The time now is 00:24.


Google+
Powered by vBulletin® Version 3.8.8 Beta 1
Copyright ©2000 - 2024, vBulletin Solutions, Inc.
Social Knowledge Networks
Powered by vBulletin® Version 3.8.8 Beta 1
Copyright ©2000 - 2024, vBulletin Solutions, Inc.

ShowCase vBulletin Plugins by Drive Thru Online, Inc.