Cruisers Forum
 


Reply
  This discussion is proudly sponsored by:
Please support our sponsors and let them know you heard about their products on Cruisers Forums. Advertise Here
 
Thread Tools Search this Thread Rate Thread Display Modes
Old 13-07-2016, 18:54   #1
Registered User
 
Reefmagnet's Avatar

Join Date: May 2008
Location: puɐןsuǝǝnb 'ʎɐʞɔɐɯ
Boat: Nantucket Island 33
Posts: 4,864
Blind rivets for mast - stainless steel or monel?

Ok, I just brought a big bag of monel blind rivets in order to attach a bunch of aluminium mast steps to my mast based on a number of recommendations when asking around and the theory that "monel corrodes less than stainless". After a bit of after-the-fact internet research, I'm wondering if this is actually true, based on readings of galvanic series charts e.g.



Further more, at least one fastener manufacturer specifically notes not to use monel for fastening aluminum, yet a lot of marine suppliers promote monel rivets as causing less galvanic corrosion than alternative stainless steel counterparts for the same application.

Considering the above, along with the premium cost of monel rivets, I'm scratching my head here for reasons why monel would be recommended at all for this application?
Reefmagnet is offline   Reply With Quote
Old 13-07-2016, 19:04   #2
Moderator
 
Jim Cate's Avatar

Join Date: May 2008
Location: cruising SW Pacific
Boat: Jon Sayer 1-off 46 ft fract rig sloop strip plank in W Red Cedar
Posts: 21,150
Re: Blind rivets for mast - stainless steel or monel?

Perhaps the issue is that the 300 series s/s can lose their passive state in use, and then their position on the series jumps markedly. I suspect that monel does not do this.

Jim
__________________
Jim and Ann s/v Insatiable II, lying Port Cygnet Tasmania once again.
Jim Cate is offline   Reply With Quote
Old 13-07-2016, 19:39   #3
Registered User
 
Reefmagnet's Avatar

Join Date: May 2008
Location: puɐןsuǝǝnb 'ʎɐʞɔɐɯ
Boat: Nantucket Island 33
Posts: 4,864
Re: Blind rivets for mast - stainless steel or monel?

Hi Jim, The closer the dissimilar metals are in voltage, the less galvanic interaction is if I read the chart correctly. This makes "active" stainless less galvanic, but I think the description of "active" is referring to the steel without it's protective oxide coating. I can't see this being the case in this particular application, which would make monel ever so slightly less galvanic than, say, 316 stainless.
Reefmagnet is offline   Reply With Quote
Old 13-07-2016, 20:12   #4
Registered User

Join Date: Aug 2009
Location: between the devil and the deep blue sea
Boat: a sailing boat
Posts: 20,420
Re: Blind rivets for mast - stainless steel or monel?

I think the answer may be that they are close on the EV scale to SS but monel being the stronger metal (?) you can go with a smaller diameter rivet. (I am thinking now in shear).

Now with the aluminum being the anode and the cathode being smaller, you reduce corrosion as compared to a SS rivet. Especially compared to a bigger dia SS rivet ...

So what we basically do here is we stick with monel, try not to oversize the rivets and use heaps of goo (Duralac, Lanocote or Tef-Gel) and we stick with anodized masts ...

Then again, in many uses, an aluminum rivet IS the better choice in an aluminum plate (just talking, I know you asked SS vs. monel only).

In any case ALWAYS punch out the cores, a step wrongly skipped over not just by homebrew skippers people but even by some less well trained riggers!

Well, just my uneducated take. Now I am going to listen to what you guys reckon.

Cheers,
b.
barnakiel is offline   Reply With Quote
Old 13-07-2016, 20:21   #5
Moderator
 
Jim Cate's Avatar

Join Date: May 2008
Location: cruising SW Pacific
Boat: Jon Sayer 1-off 46 ft fract rig sloop strip plank in W Red Cedar
Posts: 21,150
Re: Blind rivets for mast - stainless steel or monel?

Quote:
Originally Posted by Reefmagnet View Post
Hi Jim, The closer the dissimilar metals are in voltage, the less galvanic interaction is if I read the chart correctly. This makes "active" stainless less galvanic, but I think the description of "active" is referring to the steel without it's protective oxide coating. I can't see this being the case in this particular application, which would make monel ever so slightly less galvanic than, say, 316 stainless.
I'm no metallurgist, but I think that s/s can loose its passive state when exposed to stagnant water, etc, and this process is what leads to some forms of s/s corrosion. I suspect that this also leads to accelerated corrosion of aluminium it the rivet case. I hope that someone with greater knowledge will pipe up here, for I'm out of my pay grade.

Jim
__________________
Jim and Ann s/v Insatiable II, lying Port Cygnet Tasmania once again.
Jim Cate is offline   Reply With Quote
Old 13-07-2016, 20:28   #6
Registered User
 
Alan Mighty's Avatar

Join Date: Mar 2014
Location: Moreton Bay
Boat: US$4,550 of lead under a GRP hull with cutter rig
Posts: 2,135
Re: Blind rivets for mast - stainless steel or monel?

* aluminium rivets in an aluminium mast;

* coated with goo (Duralac et al.) because it's likely the two alloys (mast and rivet) of Al differ;

* punch out the cores;

* count the cores as you retrieve them and hunt for the missing until found.

But for mast steps, I would drill and tap the mast and the use an s/s machine screw well coated with goo. And schedule inspection and re-application of goo.
__________________
“Fools say that you can only gain experience at your own expense, but I have always contrived to gain my experience at the expense of others.” - Otto von Bismarck
Alan Mighty is offline   Reply With Quote
Old 13-07-2016, 21:41   #7
Registered User

Join Date: Feb 2013
Location: Oregon
Boat: Seafarer36c
Posts: 5,563
Re: Blind rivets for mast - stainless steel or monel?

[QUOTE=Alan Mighty;2166048]
* punch out the cores;

Are you nuts? the stem is where the strength is. You punch out the stem, you got nothing. Aircraft blind rivets actually have a locking collar on the stem so it can't come out. Punching out the stem and drilling off the head is how you get rid of a blind rivet.
model 10 is offline   Reply With Quote
Old 14-07-2016, 08:59   #8
Registered User
 
artisanmach's Avatar

Join Date: Aug 2013
Location: Anacortes, WA
Boat: Gulfstar 37 Sloop
Posts: 187
Re: Blind rivets for mast - stainless steel or monel?

Rivets have been used to put things together since the Bronze Age, but it usually took two workers to set them: one with a hammer to pound the rivet through the hole, the other with a bucking bar to set it on the opposite side. Then, in the mid-1930s, engineers developed blind or breakstem rivets. They let workers install fasteners from one side of a workpiece when the opposite side is inaccessible or cannot even be seen.Blind rivets are now used to assemble everything from Blind rivets come in a variety of sizes, styles, and materials.small electronic components in cell phones to steel beams in the world’s largest bridges. They join different materials of varying thickness and can handle the most demanding environments. High-tech quality control delivers foolproof installation that lets only the right rivets be installed the right way in the right holes.



How they work
A blind rivet has a smooth, hollow, cylindrical body topped by a flared head and a solid-rod mandrel with a bulbed head that extends from the hollow rivet shaft. It looks somewhat like a nail. To install one, a jaw on a setting tool grips the mandrel, pulls it into the rivet body through a drilled or punched hole in one or more layers of material. The mandrel head expands the walls of the rivet outward, pressing them firmly into the walls of the hole while forming a tightly clinched load-bearing area on the opposite side of the material. Unused parts of the mandrel break off when the tensile force exceeds that needed to fully deform the rivet body.

Rivet manufacturers put grooves on some mandrels to weaken them, in essence predetermining the spot where tension will break them. Some mandrels also have a mechanical lock that snaps into place, plugs the opening in the rivet shell, and captures the remaining portion of mandrel inside the sleeve. Installation, from the time the operator pulls the trigger to the final setting of the rivet, takes about a second and leaves a permanent, vibration-resistant joint.

The blind rivet is put on an installation tool and inserted in the prepared hole in the workpieces.
The blind rivet is put on an installation tool and inserted in the prepared hole in the workpieces.
Controlled expansion of the rivet body is accomplished through proper design and material selection. Together, they ensure uniform compression and hole fill. This, in turn, lets blind rivets join a variety of dissimilar materials, including metals, plastics, and woods.

Designers select blind rivets based on the specific applications, and mandrels for how they perform as a built-in tool. The design challenge is to combine the right rivet size and configuration (tapered, float, sharp edged, or serrated) to the right mandrel for strong joints and rivet integrity. The goal is to have rivet bodies deform as specified, and mandrels to break at precise loads to ensure joint consistency, strength, and durability.

Benefits of blind rivets
Blind rivets are the fastest way to join materials. They can be set at 150 to 500/hr, and each setting is identical. This cuts assembly time and costs. Unlike threaded fasteners, there are no concerns over tool clearance, rotation failures, and secondary parts such as bolts and tapping plates, all of which add assembly time, weight, and cost. (Tapping plates are flat parts fastened atop the workpiece to reinforce the threaded parts installed in thin materials.) Blind rivets, unlike threaded fasteners, avoid problems of over or undertorquing, and stripping. Rivets also won’t loosen once installed because the rivet body is as large or larger than the hole it’s put in. They also won’t shake out or break off, and the tight seal helps prevent leaks and seepage.

Breakstems also work in ductile materials and thin gauge metals. If necessary, rivets with large heads (at least 50% larger than the hole) can be used to spread the load further. And on soft plastics, three or four metal legs unfold diagonally across the blind surface to spread the load even further. As a rule, mandrel heads must be big enough to spread the load but not so large as to waste material and add unnecessary weight.

Blind rivets can compensate for irregular holes, as long as they are within 0.004 in. of the rivets’ expansion range. Compressing the rivet body during installation compensates for such irregularities, as do metal legs that expand the load bearing surface.

Breakstems can fasten painted parts, as well as those with other finishes without causing surface blemishes. Thread and bolt fasteners, on the other hand, can scratch, dent, and dimple surfaces.

Types of blind fasteners
There are two classes of blind fasteners: open end and closed end.

Open-end breakstems are the most common. The mandrel breaks near the blind-side head and has flanges or countersunk heads for use in thin-gauge metals and low-strength materials.

Closed-end breakstems seal holes by closing the tail end of the rivet body and capturing the mandrel inside the rivet bore. They are often used to seal liquid-handling components such as hydraulic pumps. They are not used as extensively as they once were, having been replaced by open-end versions that seal the rivet body with equal effectiveness.

Selecting and installing the right blind rivet in the right hole involves rivet diameters, grip ranges, hole preparation, head style, and corrosion resistance.Rivet diameter: Blind rivets are available in diameters from 3/32 to ¼-in., with 1/32-in. incremental increases available. Diameter selection is based on space, strength, and material thickness. The larger the diameter, the higher the shear and tensile strength, which is due to the thickness and material of the rivet body.

Grip range: The materials being joined must have a thickness that falls within a fastener’s grip range. (Grip range is the allowable difference between rivet length and material thickness.) Grip ranges increase in 1/16-in. increments, with each addition having better stem retention. A 0.5-in. grip range is usually the maximum length attained by standard breakstems, but custom designs can stretch this to an inch. Standard-size blind rivets join materials as thick as 0.75 in. Custom rivets handle materials as thin as 0.020 in., such as components for cell phones and computer chassis, or as thick as 2 in. to bridge gaps in tubular assemblies such as lawn chairs.

Hole preparation: The rivet must completely fill the hole. Principal factors that ensure this are material thickness, grip range, and rivet diameter. If a hole is too big, it will not be filled and the result is a loose rivet. If the hole is too small, the rivet won’t fit. Otherwise, no special preparation is required as long as holes are free of excessive burrs.

Head styles: There are three basic blind-rivet head styles: protruding, large flange, and countersunk. Protruding heads (also called dome or button heads) are the most common and simplest. Large flange designs have heads four to five times the size of rivet-body diameter to increase the bearing surface. Countersunk heads, after installation, are flush with the material. They are used for a better surface appearance or to reduce wind drag, such as in assembling aircraft.

Corrosion resistance: To slow or prevent corrosion, rivet bodies and mandrels are often made from identical materials, including low-carbon and stainless steels, and nickel-copper and aluminum alloys. When joining dissimilar materials, engineers specify protective coatings and sleeves to prevent corrosion or when rivets do not share the same physical and mechanical properties as the parent materials. Stainless steel breakstems offer the best corrosion protection in environments such as swimming pool ladders and city buses exposed to salt.

Installation tools
There are many types of blind-rivet installation tools, including handheld, lightweight, and semiautomated. All consist of a pulling head that grips the mandrel during rivet-body expansion.

Handheld tools install fasteners with lower break loads, typically 1,000 lb or less. They are portable and let technicians quickly install rivets of different sizes and types. Hydropneumatic hand tools are most commonly used to install blind rivets. Handheld installers can also be pneumatic, electric, or manually powered. Special nose assemblies adapt tools for putting rivets in narrow spaces, channels, insets, or right angles to the rivet body.

Up to the mid-1980s, most hand tools were steel and weighed a hefty 15 lb or more. Modern versions are lighter and more powerful. Hydropneumatic tools made from plastic and aluminum, for example, weigh an ergonomic 4 lb and set one breakstem per second. Older versions installed blind rivets within a couple seconds, but operators were slowed by having to lug heavier tools through an 8-hr shift.

Multiheaded semi and fully automatic workstations can install up to 268 breakstems simultaneously. Some of these tools also carry sophisticated monitors and foolproof sensors and controls to assure proper riveting and placement.
artisanmach is offline   Reply With Quote
Old 14-07-2016, 09:44   #9
Registered User
 
Russ's Avatar

Join Date: Jul 2008
Location: Satellite Beach, FL
Boat: Brewer 44' Steel
Posts: 393
Re: Blind rivets for mast - stainless steel or monel?

Real answer is the insulate dissimilar metals with Tef- Gel. Russ
Russ is offline   Reply With Quote
Old 14-07-2016, 10:11   #10
Registered User
 
deblen's Avatar

Join Date: Oct 2014
Location: Bay of Fundy,Grand Manan,N.B.,Canada N44.40 W66.50
Boat: Mascot 28 pilothouse motorsailer 28ft
Posts: 3,216
Images: 1
Re: Blind rivets for mast - stainless steel or monel?

If installing aluminum item to aluminum mast :
Aluminum Rivet w/Aluminum Mandrel
__________________
My personal experience & humble opinions-feel free to ignore both
.
deblen is offline   Reply With Quote
Old 14-07-2016, 10:25   #11
Moderator Emeritus
 
a64pilot's Avatar

Cruisers Forum Supporter

Join Date: Oct 2013
Location: Jacksonville/ out cruising
Boat: Island Packet 38
Posts: 31,351
Re: Blind rivets for mast - stainless steel or monel?

[QUOTE=Guy;2166066]
Quote:
Originally Posted by Alan Mighty View Post
* punch out the cores;

Are you nuts? the stem is where the strength is. You punch out the stem, you got nothing. Aircraft blind rivets actually have a locking collar on the stem so it can't come out. Punching out the stem and drilling off the head is how you get rid of a blind rivet.

I was wondering the reasoning behind that too, and sort of why nobody shoots solids in boat construction? I guess they don't know how and always default to blind rivets?

To others, he speaks of Cherry Max rivets, which usually have a steel stem in an aluminum sleeve rivet and the steel stem is locked in place once pulled, stem being the vast majority of the strength.
"Normal" Blind rivets like used in boat construction are from a structural perspective, junk, solids are much stronger but you have to be able to buck them. Cherry Max rivets are the only blind rivets that can be used to substitute a solid that I know of.
a64pilot is offline   Reply With Quote
Old 14-07-2016, 10:42   #12
Moderator
 
tkeithlu's Avatar

Cruisers Forum Supporter

Join Date: Feb 2012
Location: Carrabelle, Florida
Boat: Fiberglas shattering 44' steel trawler
Posts: 6,083
Re: Blind rivets for mast - stainless steel or monel?

That's quite a treatise, Artisanmach. Who would have thought that Alfred E. Neumann was a rivet specialist? Consider using all aluminum aircraft structural blind rivets; they are available with greater shear strength than the usual pop rivet. Try Aircraft Spruce, a major supplier to the experimental aircraft builders.
tkeithlu is offline   Reply With Quote
Old 14-07-2016, 10:47   #13
Registered User
 
Cheechako's Avatar

Join Date: Aug 2006
Location: Skagit City, WA
Posts: 25,477
Re: Blind rivets for mast - stainless steel or monel?

I've never heard of monel corroding, even with tanks in the bilge. The aluminum may be sacrificial though. Not sure. Apparently SS is further away on the scale than Monel right? Assuming passive stainless. According to that chart SS passive and SS active shouldn't be anywhere near each other! Opposite ends of the scale.
Bronze and SS , which are fairly far apart are known to work well together also.
__________________
"I spent most of my money on Booze, Broads and Boats. The rest I wasted" - Elmore Leonard











Cheechako is offline   Reply With Quote
Old 14-07-2016, 11:42   #14
Registered User

Join Date: Jul 2016
Location: Bay area
Boat: Elco Express 40 40ft
Posts: 2
Re: Blind rivets for mast - stainless steel or monel?

My understand is that monel is not good in or around salt water SS would be preferred
Blue39 is offline   Reply With Quote
Old 14-07-2016, 12:09   #15
Moderator Emeritus
 
a64pilot's Avatar

Cruisers Forum Supporter

Join Date: Oct 2013
Location: Jacksonville/ out cruising
Boat: Island Packet 38
Posts: 31,351
Re: Blind rivets for mast - stainless steel or monel?

And I thought except due to cost Monel was THE go to metal?
a64pilot is offline   Reply With Quote
Reply

Tags
mast, steel

Thread Tools Search this Thread
Search this Thread:

Advanced Search
Display Modes Rate This Thread
Rate This Thread:

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off
Trackbacks are Off
Pingbacks are Off
Refbacks are Off


Similar Threads
Thread Thread Starter Forum Replies Last Post
Removing stainless rivets from furling foils fkittson Construction, Maintenance & Refit 4 10-06-2015 13:58
Mast track rivets Cherp Deck hardware: Rigging, Sails & Hoisting 3 04-09-2014 23:44
Stainless rivets in Aluminum Cruiser2B Construction, Maintenance & Refit 3 08-01-2012 18:05
Monel vs Stainless karlhead Construction, Maintenance & Refit 14 09-10-2009 16:15
UK Supplier of 1x19 316 Wire and Monel Rivets? chris_maica Deck hardware: Rigging, Sails & Hoisting 4 02-08-2009 07:59

Advertise Here


All times are GMT -7. The time now is 01:12.


Google+
Powered by vBulletin® Version 3.8.8 Beta 1
Copyright ©2000 - 2024, vBulletin Solutions, Inc.
Social Knowledge Networks
Powered by vBulletin® Version 3.8.8 Beta 1
Copyright ©2000 - 2024, vBulletin Solutions, Inc.

ShowCase vBulletin Plugins by Drive Thru Online, Inc.