Cruisers Forum
 

Go Back   Cruisers & Sailing Forums > Search Forums
Reload this Page Search Results
Cruiser Wiki Click Here to Login
Register Vendors FAQ Community Calendar Today's Posts Log in

Showing results 1 to 22 of 22
Search took 0.00 seconds. Search: Posts Made By: wheatfieldcrows
Forum: Marine Electronics 07-11-2022, 11:55
Replies: 4
Views: 462
Posted By wheatfieldcrows
Re: Routing Cable to RAM3+ Hardwire

To close the loop, this is what I received from Standard Horizon. They confirmed it is the same for CMP30 and CMP31. Haven't tried it yet but figured I'd share.
Forum: Marine Electronics 23-10-2022, 00:50
Replies: 4
Views: 462
Posted By wheatfieldcrows
Re: Routing Cable to RAM3+ Hardwire

Interesting. Is there a higher resolution version somewhere? What is the source? It doesn't quite make a one to one connection but I think I can reverse engineer what happens off to the left of this...
Forum: Marine Electronics 22-10-2022, 10:02
Replies: 4
Views: 462
Posted By wheatfieldcrows
Routing Cable to RAM3+ Hardwire

My CMP31 RAM3+ mic is inoperable at my helm due to corroded connectors. I tired to salvage them but no go. I managed to score a 10 pin connector or have the option of just hard wiring the routing...
Forum: Construction, Maintenance & Refit 16-07-2019, 05:08
Replies: 2
Views: 1,363
Posted By wheatfieldcrows
Re: B&G T2 Ram - NAC 3 Overload

Not yet, I'm going to take the motor off and ensure that it is turning when the power is supplied. Wont have a chance to do so until Wednesday night. The unit is brand new so hard to believe they...
Forum: Construction, Maintenance & Refit 15-07-2019, 06:59
Replies: 2
Views: 1,363
Posted By wheatfieldcrows
B&G T2 Ram - NAC 3 Overload

I recently ditched the wheel pilot on my Pearson 424 and installed a B&G autopilot setup with a B&G T2 linear actuator and a NAC-3 computer. Over the weekend I got it to the point where the system...
Forum: Engines and Propulsion Systems 27-08-2018, 22:15
Replies: 37
Views: 15,134
Posted By wheatfieldcrows
Re: Yanmar YSM 12 - Troubleshooting Help

Well that’s good to know, maybe I did breath too much exhaust after all. Well mine are all perfectly aligned now for that high performance YSM-12 feeling.
Forum: Engines and Propulsion Systems 27-08-2018, 21:43
Replies: 37
Views: 15,134
Posted By wheatfieldcrows
Re: Yanmar YSM 12 - Troubleshooting Help

Ok... so it has been awhile but finally got a used head in hand and cleaned it up. Didn’t lap the valves which I already regret but threw the head on and with my brand spakin’ new injector the spray...
Forum: The Sailor's Confessional 03-07-2018, 10:28
Replies: 106
Views: 25,241
Posted By wheatfieldcrows
Re: Embarrassing story, seeking advice

You have nothing to worry about......
Forum: Boats For Sale and Wanted 03-07-2018, 07:47
Replies: 4
Views: 1,056
Posted By wheatfieldcrows
Re: Used Yanmar YSM 12 - Cylinder head

Yeah, turns out I need a new head. Posted photos in the other thread. For anyone else who wants to watch a slow motion train wreck...

...
Forum: Engines and Propulsion Systems 03-07-2018, 07:39
Replies: 37
Views: 15,134
Posted By wheatfieldcrows
Re: Yanmar YSM 12 - Troubleshooting Help

After close inspection it would appear all the bits of metal were not just from the precombustion chamber but also from the head itself. It would seem the well that the injector and chamber fit into...
Forum: Boats For Sale and Wanted 02-07-2018, 17:11
Replies: 4
Views: 1,056
Posted By wheatfieldcrows
Used Yanmar YSM 12 - Cylinder head

My cylinder head for my YSM 12 is cracked in a way that prevents a fix with welding.

I know it is unlikely that someone might have one of these lying around but I figured I'd give it a shot before...
Forum: Engines and Propulsion Systems 02-07-2018, 14:10
Replies: 37
Views: 15,134
Posted By wheatfieldcrows
Re: Yanmar YSM 12 - Troubleshooting Help

Well, gave it my all including a slide hammer and blow torch. Finally dropped it off at the machine shop. They got it out but I think they destroyed the pre combustion chamber in the process. Got a...
Forum: Engines and Propulsion Systems 15-06-2018, 06:37
Replies: 37
Views: 15,134
Posted By wheatfieldcrows
Re: Yanmar YSM 12 - Troubleshooting Help

Anyone have a favorite marine diesel shop in Kemah, Tx?
Forum: Engines and Propulsion Systems 15-06-2018, 06:31
Replies: 37
Views: 15,134
Posted By wheatfieldcrows
Re: Yanmar YSM 12 - Troubleshooting Help

Well I built a crappy version of an injector puller with parts I had around and it just bent the plate pretty easily. I then built a hardier version with steel HSS and grade 8 bolts and managed to...
Forum: Engines and Propulsion Systems 12-06-2018, 20:25
Replies: 37
Views: 15,134
Posted By wheatfieldcrows
Re: Yanmar YSM 12 - Troubleshooting Help

Well I may have tried to edit my update post too many times as it got sent to the mods for approval but long story short injector is stuck with a capital S in the head. Building an extractor for...
Forum: Engines and Propulsion Systems 12-06-2018, 20:21
Replies: 37
Views: 15,134
Posted By wheatfieldcrows
Re: Yanmar YSM 12 - Troubleshooting Help

Well a day later than I thought but made it down to the boat tonight. Adjusted the valves which was easy but no start. Bled the fuel again and cracked the injector fuel lines and saw pressure...
Forum: Engines and Propulsion Systems 12-06-2018, 20:06
Replies: 37
Views: 15,134
Posted By wheatfieldcrows
Re: Yanmar YSM 12 - Troubleshooting Help

In poking my head way around back there does seem to be a good bit of surface rust on the aft side of the head. If compression shows low I may try swapping head gaskets before pulling the whole thing...
Forum: Engines and Propulsion Systems 12-06-2018, 20:03
Replies: 37
Views: 15,134
Posted By wheatfieldcrows
Re: Yanmar YSM 12 - Troubleshooting Help

Well a day later than I thought but made it down to the boat tonight. Adjusted the valves which was easy but no start. Bled the fuel again and cracked the injector fuel lines and saw pressure there.....
Forum: Engines and Propulsion Systems 11-06-2018, 06:24
Replies: 37
Views: 15,134
Posted By wheatfieldcrows
Re: Yanmar YSM 12 - Troubleshooting Help

Thanks for the advice. From memory the exhaust valve rocker had way more clearance than 0.2 mm so that definitely needs to be adjusted. I guess I should have read the manual first! Sometimes I just...
Forum: Engines and Propulsion Systems 10-06-2018, 18:16
Replies: 37
Views: 15,134
Posted By wheatfieldcrows
Re: Yanmar YSM 12 - Troubleshooting Help

And now with video evidence for the side to side play of the exhaust valve rocker...


Also here because not sure uploading the video to CF worked... https://youtu.be/avWK16wpTzA?t=5
Forum: Engines and Propulsion Systems 10-06-2018, 16:25
Replies: 37
Views: 15,134
Posted By wheatfieldcrows
Yanmar YSM 12 - Troubleshooting Help

I have a Yanmar YSM 12 in a 1979 Hunter 30. It is a 1 cylinder 12 hp diesel. We are getting ready to sell her because we have our eyes on a bigger boat but the engine wont start. I'll admit that we...
Forum: Liveaboard's Forum 02-11-2017, 13:41
Replies: 1,369
Views: 354,660
Posted By wheatfieldcrows
Re: Youtube liveaboard stars?

You aren't paying for the water. You are paying for other people to produce a bottle that is cheap enough to be disposable and put the water in it because you want the convenience.
Showing results 1 to 22 of 22

 
Forum Jump


All times are GMT -7. The time now is 16:08.

Contact Us - Cruisers & Sailing Forums - Sitemap - Community Rules - Terms of Service - Privacy - Accessibility - Top

Google+
Powered by vBulletin® Version 3.8.8 Beta 1
Copyright ©2000 - 2024, vBulletin Solutions, Inc.
Social Knowledge Networks
Powered by vBulletin® Version 3.8.8 Beta 1
Copyright ©2000 - 2024, vBulletin Solutions, Inc.
close

Privacy Guaranteed - your email is never shared with anyone, opt out any time.


ShowCase vBulletin Plugins by Drive Thru Online, Inc.