Cruisers Forum
 


Join CruisersForum Today

Reply
 
Thread Tools Search this Thread Rate Thread Display Modes
Old 26-05-2020, 14:23   #1
Registered User

Join Date: Apr 2019
Posts: 6
Volvo parts needed

Hi All,

I have a Volvo D2-75 that has a silencer that comprised of two Stainless end plates in a couple foot section of 8" radiator/exhaust hose. The end plates have numerous corrosion pinholes, I have used some epoxy to seal the end caps, but would like to replace with new if possible....

The part numbers are 842764 and 842765. They are listed as discontinued.

Just hoping that someone could suggest a source or actually has the two parts needed...

Also, if you have any suggestions for alternatives courses of action that would be very much appreciated too!!!!

Thanks for your time, love this site!!!

Dave
__________________

bastikriol is offline   Reply With Quote
Old 26-05-2020, 16:48   #2
Registered User

Join Date: Jan 2013
Location: Majuro, Marshall Islands
Boat: Nordic 44
Posts: 26
Re: Volvo parts needed

I have a D2-55E, and have had to deal many times with superseded part numbers. I have found Marine Parts Express to be a highly reliable source of information and parts. I would suggest starting with the 'engine search':


The One List - Marine Parts Express


Click your specific D2-75 (A, B, C, etc.), then do a 'part no. search', using the part numbers you have.


Alternatively, you can go the schematics library for your engine model, via this route:


Volvo Penta Schematics - Marine Parts Express


On this page, select


D2-75A_D2-75B_D2-75C_D2-75F

'Silencer inlet' looks like what you're looking for. The schematic will refer to current part numbers.


Good luck.
__________________

Lehua-kona is offline   Reply With Quote
Old 26-05-2020, 17:31   #3
Registered User
 
Dsanduril's Avatar

Join Date: Aug 2011
Location: Petersburg, AK
Boat: Outremer 50S
Posts: 3,151
Re: Volvo parts needed

If you can't find/don't like the price of Volvo parts Vetus makes a whole lot of exhaust components that are all plastic (no corrosion) except for the fasteners. Our D2-40 doesn't come with the same Volvo silencer, but our old engine had one. Replaced it with Vetus, and the current engines came with Vetus waterlocks installed by the Volvo dealer. May be an option, but then you have to figure out new mounting, etc. as they are not a direct drop-in replacement.
Dsanduril is offline   Reply With Quote
Old 26-05-2020, 17:44   #4
Registered User

Join Date: Apr 2019
Posts: 6
Re: Volvo parts needed

Thanks for you suggestions, I will look into it... I am really hoping to keep the costs down, so I was hoping to locate the actual parts... right now they are "repaired" but I hate have more than myself to worry about!
bastikriol is offline   Reply With Quote
Old 26-05-2020, 17:52   #5
Registered User
 
Dsanduril's Avatar

Join Date: Aug 2011
Location: Petersburg, AK
Boat: Outremer 50S
Posts: 3,151
Re: Volvo parts needed

Just so we're all clear, is this the unit you are looking at? The SS end caps are getting holes?



Pretty sure I've seen those other than Volvo, but can't recall where, if the picture is correct maybe it will jog someone else's memory.
Dsanduril is offline   Reply With Quote
Old 26-05-2020, 18:09   #6
Registered User

Join Date: Apr 2019
Posts: 6
Re: Volvo parts needed

Yes sir, that is the whole unit assembled. I am looking for and part numbers I provided are for the Stainless end pieces. The whole unit can be had for about $700...

I hate spending that much for the 2 end caps, section of hose and hose clamps...

Thank you for clarifying and providing the picture....

Best,

-Dave
bastikriol is offline   Reply With Quote
Old 26-05-2020, 18:33   #7
Marine Service Provider

Join Date: Sep 2014
Location: Auckland, NZ
Boat: Compass 790 , 7.9 metres or 26 ft
Posts: 1,555
Re: Volvo parts needed

I'd agree with Dsanduril, get a fibre reinforced plastic muffler to replace it. There are plenty of types that will work.
I make my own stainless ones but FRP is better after water injection.
However if you are fixed on stainless try a few stainless fabrication places. I'm sure they could make you one cheaper.
Compass790 is online now   Reply With Quote
Old 26-05-2020, 18:56   #8
Registered User

Join Date: Apr 2019
Posts: 6
Re: Volvo parts needed

I am not fixed on Stainless, I like the idea of non corrosive materials, but I want to go cheap as possible right now... Thanks for you suggestion!!!
bastikriol is offline   Reply With Quote
Old 26-05-2020, 19:10   #9
Registered User
 
Dsanduril's Avatar

Join Date: Aug 2011
Location: Petersburg, AK
Boat: Outremer 50S
Posts: 3,151
Re: Volvo parts needed

I feel your pain but am struggling to recall if I ever found a source other than Volvo. I do know that at one point I pulled the hose off the unit and put epoxy all over the inside ends of the drum (both ends) to seal the same kinds of pinholes you are describing. So, not an unknown problem.
Dsanduril is offline   Reply With Quote
Old 26-05-2020, 19:18   #10
Marine Service Provider

Join Date: Sep 2014
Location: Auckland, NZ
Boat: Compass 790 , 7.9 metres or 26 ft
Posts: 1,555
Re: Volvo parts needed

Quote:
Originally Posted by Dsanduril View Post
I feel your pain but am struggling to recall if I ever found a source other than Volvo. I do know that at one point I pulled the hose off the unit and put epoxy all over the inside ends of the drum (both ends) to seal the same kinds of pinholes you are describing. So, not an unknown problem.
Yes this is a good idea too.
He can glass over all except the pipe ends as well. I glassed over a plastic muffler that had a hole in it & lasted 5 years & probably a lot more ( sold the boat)

I meant OP can find a muffler that will do the job but might have to make his own mounts etc if he wants to avoid being reamed by Volvo
Compass790 is online now   Reply With Quote
Old 26-05-2020, 19:57   #11
Registered User
 
Dsanduril's Avatar

Join Date: Aug 2011
Location: Petersburg, AK
Boat: Outremer 50S
Posts: 3,151
Re: Volvo parts needed

Palby Marine may be worth contacting, doesn't look like an exact match, but pretty close, and if they use the same size hoses then might not be a big deal. Looks like their whole new unit is available for ~1/2 Volvo's price (in Europe).

Another link
Dsanduril is offline   Reply With Quote
Old 26-05-2020, 20:02   #12
Registered User

Join Date: Jul 2014
Location: Seattle, WA
Boat: Hallberg-Rassy 36
Posts: 48
Re: Volvo parts needed

Google "fiberglass muffler from Centek" I was informed one of the boats in our fleet had his replacement made for a meer $170!


I have no connection to the company .



PNWSalmon is offline   Reply With Quote
Old 27-05-2020, 12:40   #13
Registered User

Join Date: Nov 2014
Posts: 1,169
Re: Volvo parts needed

I may have a couple of those end plates....I think 3.5” inlet & outlet hose diameter. What hose size do you need?
DougR is offline   Reply With Quote
Old 28-05-2020, 07:20   #14
Registered User

Join Date: Nov 2014
Posts: 1,169
Re: Volvo parts needed

Hello Bastikriol,
I did some digging in my garage and I found the muffler you need.....
Part # 842768. End plates # 842764 and 842765.
89mm/3.5”. Hose size

Send me a PM if you’re interested.

DougR
Attached Thumbnails
Click image for larger version

Name:	B999D333-EACC-4773-B5EA-BBA018E4E5A7.jpg
Views:	8
Size:	411.0 KB
ID:	215964   Click image for larger version

Name:	CAC72206-11B3-4211-8ACA-70CD6A3D4212.jpg
Views:	9
Size:	363.6 KB
ID:	215965  

DougR is offline   Reply With Quote
Old 28-05-2020, 07:28   #15
Registered User
 
Dsanduril's Avatar

Join Date: Aug 2011
Location: Petersburg, AK
Boat: Outremer 50S
Posts: 3,151
Re: Volvo parts needed

The joys of the internet Here's someone looking for a somewhat difficult to source part, and someone else who just happens to have one in their garage!
__________________

Dsanduril is offline   Reply With Quote
Reply

Tags
parts, volvo

Thread Tools Search this Thread
Search this Thread:

Advanced Search
Display Modes Rate This Thread
Rate This Thread:

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off
Trackbacks are Off
Pingbacks are Off
Refbacks are Off


Similar Threads
Thread Thread Starter Forum Replies Last Post
Have boat & need parts OR Have parts & need buyers? CatBoatDoug Our Community 0 22-11-2016 06:30
Volvo Penta parts needed - MD7B aquabrat Engines and Propulsion Systems 1 24-07-2014 08:14
For Sale or Trade: Alternators, panel and misc. Universal diesel parts parts canvasman Classifieds Archive 0 10-03-2014 09:17

Advertise Here


All times are GMT -7. The time now is 21:34.


Google+
Powered by vBulletin® Version 3.8.8 Beta 1
Copyright ©2000 - 2020, vBulletin Solutions, Inc.
Social Knowledge Networks
Powered by vBulletin® Version 3.8.8 Beta 1
Copyright ©2000 - 2020, vBulletin Solutions, Inc.

ShowCase vBulletin Plugins by Drive Thru Online, Inc.