Cruisers Forum
 


Reply
  This discussion is proudly sponsored by:
Please support our sponsors and let them know you heard about their products on Cruisers Forums. Advertise Here
 
Thread Tools Search this Thread Rate Thread Display Modes
Old 29-04-2018, 05:35   #1
Registered User

Join Date: Oct 2017
Posts: 3
Morgan 462 Ketch Replacement Halyards

Help please...I have a 1981 Morgan 462 Ketch. I need new genoa, main and mizzen halyards.
The owners manual states the main and mizzen are 3/8 inch and the genoa is wire rope. My gear has obviously been changed at some point.

The main and genoa are all rope and at least 1/2 while the Mizzen is 7/16.

I do not feel that 3/8 is suitable for sails this size? Maybe okay on the mizzen? Your recommendations. I am making a couple of assumptions, the sheaves have been changed as there is no binding or issues with any of the halyards.

Who do you recommend for a rigging house, I have none local and will need new shackles pre spliced.
wesswank is offline   Reply With Quote
Old 29-04-2018, 06:29   #2
Registered User
 
Sailmonkey's Avatar

Join Date: Sep 2009
Location: Houston
Boat: ‘01 Catana 401
Posts: 9,627
Re: Morgan 462 Ketch Replacement Halyards

Where are you local to?

3/8” I feel is adequate, especially so if you use spectra or dyneema cored halyards.
Sailmonkey is offline   Reply With Quote
Old 29-04-2018, 06:37   #3
Senior Cruiser
 
skipmac's Avatar

Cruisers Forum Supporter

Join Date: Oct 2007
Location: 29° 49.16’ N 82° 25.82’ W
Boat: Pearson 422
Posts: 16,306
Re: Morgan 462 Ketch Replacement Halyards

For a cruising boat most riggers recommend polypropylene for halyards like Sta-Set from New England ropes or similar from other suppliers. If you're a little more performance oriented or don't mind a little extra cost then one of the more high tech cored ropes gives less stretch. I agree that 3/8" seems a little small. Online guides recommend 7/16" min for the main and jib halyards. Mizzen you could probably do 3/8" however, a little larger sizes can be a bit easier on the hands.

I wouldn't assume the sheaves have been changed. On older boats many sheaves were designed for wire and rope and usually work OK with all rope.

As far as a rigger, you don't mention where you are. The forum is international with members from all over the globe. USA I'm guessing? East or west coast, north or south?
__________________
The water is always bluer on the other side of the ocean.
Sometimes it's necessary to state the obvious for the benefit of the oblivious.
Rust is the poor man's Loctite.
skipmac is offline   Reply With Quote
Old 29-04-2018, 07:17   #4
Registered User

Join Date: Mar 2016
Location: New England. USA.
Boat: McCurdy & Rhodes Custom 46
Posts: 1,483
Re: Morgan 462 Ketch Replacement Halyards

Sta-set is Polyester not polypropylene. Polypropylene is not u.v. resistant and would also be terrible on your hands. Sta-set is my go to line. It’s good stuff.

Are your halyard winches self tailing? If so they may dictate your diameter range. If they are not your hands will be much happier with the current size than 3/8.
dfelsent is offline   Reply With Quote
Old 29-04-2018, 07:58   #5
Senior Cruiser
 
skipmac's Avatar

Cruisers Forum Supporter

Join Date: Oct 2007
Location: 29° 49.16’ N 82° 25.82’ W
Boat: Pearson 422
Posts: 16,306
Re: Morgan 462 Ketch Replacement Halyards

Quote:
Originally Posted by dfelsent View Post
Sta-set is Polyester not polypropylene. Polypropylene is not u.v. resistant and would also be terrible on your hands. Sta-set is my go to line. It’s good stuff.

Sorry, had a brain fart. You are absolutely correct, Sta-Set is polyester. Polypropylene is typically found in the cheap, floating lines like used in ski ropes, one of the few applications where polypropylene is appropriate.
__________________
The water is always bluer on the other side of the ocean.
Sometimes it's necessary to state the obvious for the benefit of the oblivious.
Rust is the poor man's Loctite.
skipmac is offline   Reply With Quote
Old 29-04-2018, 09:16   #6
Registered User
 
Davidhoy's Avatar

Join Date: Jul 2016
Location: West Palm Beach, FL
Boat: Catalina 470
Posts: 1,131
Re: Morgan 462 Ketch Replacement Halyards

Welcome to CF, wesswank! Fellow Morgan 462 owner here, located in the Fort Lauderdale area. There is/was a 1981 M462 for sale in FLL, is that the one you bought?

I am planning on replacing my running rigging soon, but am waiting until I'm a little closer to my departure for the wild blue yonder. I spoke with a couple of vendors in the area about new halyards, sheets, etc. I'll see if I can find the quotes I got with all the details...

Regards,
David.
__________________
“Twenty years from now you will be more disappointed by the things that you didn't do than by the ones you did do. So throw off the bowlines. Sail away from the safe harbor. Catch the trade winds in your sails. Explore. Dream. Discover.” – Mark Twain
Davidhoy is offline   Reply With Quote
Old 29-04-2018, 09:47   #7
Registered User

Join Date: Sep 2011
Location: Tarpon Springs fl
Boat: Morgan 384/ 1982
Posts: 378
Images: 3
Re: Morgan 462 Ketch Replacement Halyards

38 morgan here Stay set 3/8 will do the job strength wise , you can go a little larger just for comfort, buy not necessary at all. Look at the working load and breaking strength.
And if you get new ever 10 years you will be way ahead of wear out !
stnick is offline   Reply With Quote
Old 29-04-2018, 11:07   #8
Registered User
 
S/V Alchemy's Avatar

Join Date: May 2008
Location: Nova Scotia until Spring 2021
Boat: Custom 41' Steel Pilothouse Cutter
Posts: 4,976
Re: Morgan 462 Ketch Replacement Halyards

Quote:
Originally Posted by Sailmonkey View Post
Where are you local to?

3/8” I feel is adequate, especially so if you use spectra or dyneema cored halyards.
This. I replaced 1/2 inch Dacron with 1/2 inch Dacron with 6 mm Dyneema core just for the hand feel, existing sheave groove width and existing stoppers. But the difference is significant in terms of less stretch. So if you stay with 3/8" but with (for example) 4 mm Dyneema cores, you are very much ahead of the game.

I don't feel Dyneema cores are preferable in a cruising context for sheets, but for halyards, they are a real improvement.
__________________
Can't sail? Read about our travels at https://alchemyonpassage.blogspot.com/. Can't sleep? Read www.alchemy2009.blogspot.com for fast relief. Can't read? Avoid www.volumesofsalt.blogspot.com, because it's just personal reviews of sea books.
S/V Alchemy is offline   Reply With Quote
Old 29-04-2018, 12:01   #9
Registered User

Join Date: Dec 2009
Location: Cruising, now in USVIs
Boat: Taswell 43
Posts: 1,053
Re: Morgan 462 Ketch Replacement Halyards

Our 43' Taswell (Cutter rig) received all new halyards when we redidnour mast and rigging. Originally, we had all cable. We switched and went with 6mm Dyneema-and had no issues since we made the change in 2011-light weight, small size, easy to handle, no stretch, etc, etc. But one big decision point may be the type of rig you have. Our sails (all 3=H/S, S/S, and M/S) are on roller furlers, so the only time we mess with the halyards is at the start and end of the season. If yours is a conventional rig, where you need to pull on the halyards every time you want to set a sail, and if you don't have electric (or hyd) winches, you'd surely want to find some line that is kind to your hands. Lots of variables.
sailcrazy is offline   Reply With Quote
Old 29-04-2018, 12:10   #10
Registered User

Join Date: Feb 2015
Boat: Land bound, previously Morgan 462
Posts: 1,994
Re: Morgan 462 Ketch Replacement Halyards

I have a Morgan 462- I replaced the 3/8 halyards with 9/16 Sta-set back in 1998. Yes it is overkill, but at the time there was no Dyneema or whatever, or at least I didn't know about it, and I figured 9/16 would have less stretch than 1/2 and will last longer and when I go aloft I like the look of a big line. Existing sheaves and winches on my M462 were fine with 9/16.
waterman46 is offline   Reply With Quote
Old 29-04-2018, 12:25   #11
Moderator Emeritus
 
roverhi's Avatar

Join Date: Aug 2005
Location: Carlsbad, CA
Boat: 1976 Sabre 28-2
Posts: 7,505
Send a message via Yahoo to roverhi
Re: Morgan 462 Ketch Replacement Halyards

All Dacron halyards like StaSet will have significant stretch with standard double braid or a little less with parallel core like StaSet X. Exotic cored line will have significantly less to virtually no stretch with resistance to stretch commensurate with price. FWIW, have 5/16" T900 exotic on the main halyard on my 28' boat and it has virtually no stretch, possibly less than the wire halyard it replaced. 3.8" exotic cored rope would be more than adequate for strength for a boat your size but might go up to 7/16" for hand comfort. If you're sticking with dacron, 1/2" to compensate for stretch would be a good idea. NE VPC or other hybrid cored line which are a middle ground between all Dacron and full exotic cored line for stretch. VPC has worked out for me for other halyards on my 35' boat.

Back in the good old days of hank on jibs, headsail halyards needed to have low stretch halyards to reduce scalloping between hanks as the wind speed varied. With the foils of roller furling, headsail tension is much less a factor and doesn't really need larger or extreme low stretch halyards.

Have used rope halyards in the wire/rope dual purpose sheaves for more than 40 years. You shouldn't have a problem switching to rope with those masthead sheaves. Still not a bad idea to go up and have a look at the sheaves to be sure that the wire hasn't caused burrs that might abraid a rope halyard. Actually going to the masthead and having a look around is a good idea. No telling what you'll find up there. When I got my ATN Mast Climber went to the mast head just to try it out. Found two broken strands in the headstay wire at the masthead swage. Possibly saved myself from a dismasting.
__________________
Peter O.
'Ae'a, Pearson 35
'Ms American Pie', Sabre 28 Mark II
roverhi is offline   Reply With Quote
Old 29-04-2018, 15:44   #12
Registered User
 
skipgundlach's Avatar

Join Date: Mar 2003
Location: Currently on the boat, somewhere on the ocean, living the dream
Boat: Morgan 461 S/Y Flying Pig
Posts: 2,298
Send a message via Skype™ to skipgundlach
Re: Morgan 462 Ketch Replacement Halyards

Our 461 has larger sails in all regards/instances than your 462...

When we got it, we had 9/16 sheets and halyards.

We went with 7/16 StaySetX for halyards and StaySet for sheets.

When we had some minor damage on the genoa sheet (looped, not knotted), and installed running backs, we took that sheet and used it (cut in half) for those blocks. We went with 1/2" Regatta Braid, which is very much nicer on the hands and as floppy as a wet noodle. It's now 5 years old and doing great.

Your winches (assuming they are self-tailing) will perhaps determine the smallest you can go. It's possible you can drop to 3/8 in terms of strength, but having that on our dinghy davits' blocks, I can tell you that it's not much to grab (thin = easy-to-slip-through-your-hands), with even that small weight.

YMMV but I'd suggest 7/16 StaySetX (next to no stretch) premade by West (or Port if you have a pro card) with shackles for the halyards, and Regatta Braid for the sheets (the sheets - unless you're racing - likely don't need to be next-to-no stretch), as it's very much easier on the hands.

L8R

Skip
__________________
Morgan 461 #2 SV Flying Pig, KI4MPC
See our galleries at www.justpickone.org/skip/gallery!
skipgundlach is offline   Reply With Quote
Reply

Tags
halyard, ketch, men, morgan

Thread Tools Search this Thread
Search this Thread:

Advanced Search
Display Modes Rate This Thread
Rate This Thread:

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off
Trackbacks are Off
Pingbacks are Off
Refbacks are Off


Similar Threads
Thread Thread Starter Forum Replies Last Post
Morgan 462 tallboy Monohull Sailboats 21 20-01-2014 06:19
For Sale: Morgan 462 Ketch - BVI adeliajo Classifieds Archive 45 08-03-2012 14:21
For Sale: Morgan 462 rlequerica Classifieds Archive 7 22-04-2011 21:17
Greetings - looking for info on Morgan 462 cabo_sailor Monohull Sailboats 2 21-03-2008 19:27

Advertise Here


All times are GMT -7. The time now is 19:05.


Google+
Powered by vBulletin® Version 3.8.8 Beta 1
Copyright ©2000 - 2024, vBulletin Solutions, Inc.
Social Knowledge Networks
Powered by vBulletin® Version 3.8.8 Beta 1
Copyright ©2000 - 2024, vBulletin Solutions, Inc.

ShowCase vBulletin Plugins by Drive Thru Online, Inc.