Cruisers Forum
 


Reply
  This discussion is proudly sponsored by:
Please support our sponsors and let them know you heard about their products on Cruisers Forums. Advertise Here
 
Thread Tools Search this Thread Rate Thread Display Modes
Old 25-05-2013, 06:38   #61
Registered User

Join Date: Jan 2009
Location: San Diego, currently in Greece
Boat: Hallberg-Rassy 40
Posts: 357
Images: 4
re: Rolling Hitch on Snubber

Transmitterdan,

Regarding climbing ropes:

A dynamic rope is a specially constructed, stretchable rope. This 'stretch' is what makes it 'dynamic', in contrast to a static rope that doesn't have any give when under load. By stretching under load, a dynamic rope will soften the impact of extreme stresses on it, such as falls, and lessens the likelihood of failure. This is particularly useful in rock climbing, where it can absorb much of the energy of a fall
jim_thomsen is offline   Reply With Quote
Old 25-05-2013, 06:50   #62
Registered User
 
AnchorageGuy's Avatar

Join Date: Mar 2003
Location: Wherever the boat is!
Boat: Marine Trader 34DC
Posts: 4,619
re: Rolling Hitch on Snubber

Lots of good info, but my thoughts on the original posting question. I see 3 issues that may have contributed to the failure. Number one is the use of dacron, a snubber needs to stretch to prevent the shock loads of the chain. Nylon would be a better choice IMO. Using braid instead of 3 strand, braid will build up heat in the core as it tries to stretch and the inner core will "melt" causing it to fail. The outer braid does not have the strength to take the load. Number 3, the line does look to me to be a bit small to be used as a snubber based on Evans advertised boat size and type. I'm no expert but I did sleep in a Holiday Inn Express last week. Chuck
__________________
Chesapeake Bay, ICW Hampton Roads To Key West, The Gulf Coast, The Bahamas

The Trawler Beach House
Voyages Of Sea Trek
AnchorageGuy is offline   Reply With Quote
Old 25-05-2013, 06:53   #63
Registered User
 
Kettlewell's Avatar

Join Date: Jul 2006
Location: Massachusetts
Boat: Finnsailer 38
Posts: 5,823
re: Rolling Hitch on Snubber

A few comments on various things. I use a 3/8" 3-strand snubber on a 38-foot, 20000 lb. boat, and I have never had one break. So far, the highest it has seen was 56-60 knots, did not slip, did not break, appeared fine, kept using it for a long time afterwards. On my previous boat, a 32-foot cat, we went through Hurricane Bob with a 3/8" snubber on there, and nothing broke. I have had a chain hook fall off numerous times, but always in light winds when it is not a big deal--I can hear the chain rumbling which lets me know. I keep the deck end of the snubber cleated off so it can just be let go in an emergency. I have had to do that a few times in very high winds, but later pulled the snubber back onboard because the rolling hitch kept it on the chain. I do slap on a few extra half hitches to keep the hitch tight, and I use extra turns around the chain--never slips, and never jams when you want it undone. I've also used it around line in order to take the strain and chafe off the main rope rode, and it works well for that too.

I also use a chain hook, particularly in normal light air anchoring, or for short stops, or for backing down the anchor when I don't put out a long snubber. I have had the line break right where it goes into the eye of the chain hook, but due to old age--should have been replaced long before.
__________________
JJKettlewell
"Go small, Go simple, Go now"
Kettlewell is offline   Reply With Quote
Old 25-05-2013, 07:27   #64
Registered User
 
mbianka's Avatar

Join Date: Mar 2008
Posts: 2,216
Images: 1
re: Rolling Hitch on Snubber

I'm trying to picture what I do for the snubber line. I think it's just using two or three half hitches that secure it to the chain. Never had it slip or chafe at the knot/chain area. Comes up easily through the chain roller and is untied on deck.
__________________
Mike
mbianka is offline   Reply With Quote
Old 25-05-2013, 07:37   #65
Registered User
 
Kettlewell's Avatar

Join Date: Jul 2006
Location: Massachusetts
Boat: Finnsailer 38
Posts: 5,823
Re: Rolling Hitch on Snubber

One other thing on the reports of cyclic loading causing 3-strand nylon to overheat and melt. Obviously, it can do so based on a few reports from reliable folks, but it takes some very extreme conditions to get to that point--we're talking over 100 knots and exposed conditions creating big waves. It has never happened to me, and I have never seen an example of it in the real world, and I looked at a lot of broken lines after Hurricane Bob--they all were due to ordinary chafe problems. Lots of moorings--I would guess the majority, still use ordinary 3-strand in fairly hefty sizes. So, yes, if you are expecting a hurricane in an exposed location, it might be something worth considering, but short of that I don't think you have to worry about it.
__________________
JJKettlewell
"Go small, Go simple, Go now"
Kettlewell is offline   Reply With Quote
Old 25-05-2013, 07:41   #66
Moderator
 
noelex 77's Avatar

Cruisers Forum Supporter

Join Date: Jul 2007
Boat: Bestevaer.
Posts: 15,161
Re: Rolling Hitch on Snubber

I think a must of offended the god of snubbers in a previous life because a well as my rolling hitches slipping, I break a least one snubber a year, usually a couple.

I am hoping its its the lousy nylon that sold here. The local fisherman buy more on price than quality.
I have just received some octiplat from the UK and I have my fingers crossed for no more broken snubbers.
noelex 77 is offline   Reply With Quote
Old 25-05-2013, 07:42   #67
Writing Full-Time Since 2014
 
thinwater's Avatar

Join Date: Nov 2008
Location: Deale, MD
Boat: PDQ Altair, 32/34
Posts: 10,118
Re: rolling hitch on snubber

Quote:
Originally Posted by estarzinger View Post
...........
Climbing rope for snubber. Yes, I thought about you when I switched from polyester to Dyneema (free as part of a test group). Big mistake, dynamic climbing rope would CERTAINLY be better, but too large for my application.

Energy absorption and climbing rope. For a limited number of impacts over the sorts of turns knots make, climbing ropes are rated for about 200 ft-pounds/foot of absorption, but over a longer term, let us say 1/2 of that. So with 20 feet out it should handle about 2000 ft-pound surges.

Assuming your boat weighs 25,000 pounds (wild guess--no idea) and a surge has you moving 3 ft/sec, the energy is 3500 ft-pounds. The chain will absorb a good part of that, but still we can see that the rope is going to be operating in the range where it will eventually fail from fatigue. If it had been spliced around a thimble, probably not.

It seems that the lesson may simply be to trim the last 2 feet off every 40-80 nights (guessing), depending on how bad the exposure has been.

I'm following this with interest because I am thinking of going to a 8.5 mm climbing rope bridle on a 8000 pound cat; I have something heavier now and could benefit from the increased shock absorption, since my rode is now all-chain. I use a chain plate, so the knot bit does not concern me.
__________________
Gear Testing--Engineering--Sailing
https://sail-delmarva.blogspot.com/
thinwater is offline   Reply With Quote
Old 25-05-2013, 07:43   #68
Registered User
 
Kettlewell's Avatar

Join Date: Jul 2006
Location: Massachusetts
Boat: Finnsailer 38
Posts: 5,823
Re: Rolling Hitch on Snubber

Quote:
I think a must of offended the god of snubbers in a previous life because a well as my rolling hitches slipping, I break a least one snubber a year, usually a couple.
Where do they break?
__________________
JJKettlewell
"Go small, Go simple, Go now"
Kettlewell is offline   Reply With Quote
Old 25-05-2013, 07:53   #69
Writing Full-Time Since 2014
 
thinwater's Avatar

Join Date: Nov 2008
Location: Deale, MD
Boat: PDQ Altair, 32/34
Posts: 10,118
Re: Rolling Hitch on Snubber

Quote:
Originally Posted by Kettlewell View Post
One other thing on the reports of cyclic loading causing 3-strand nylon to overheat and melt. Obviously, it can do so based on a few reports from reliable folks, but it takes some very extreme conditions to get to that point--we're talking over 100 knots and exposed conditions creating big waves. It has never happened to me, and I have never seen an example of it in the real world, and I looked at a lot of broken lines after Hurricane Bob--they all were due to ordinary chafe problems. Lots of moorings--I would guess the majority, still use ordinary 3-strand in fairly hefty sizes. So, yes, if you are expecting a hurricane in an exposed location, it might be something worth considering, but short of that I don't think you have to worry about it.
I posted some calculations on that topic.
Sail Delmarva: Can Nylon Anchor Rope be Melted by a Severe Cycling Load ? Myth Plausible.
I've actually broken ropes on test rigs and looked at the ends. It seems to be about rope diameter and heat dissipation; the rope has to be fat to build heat. Certainly possible and I believe the stories. A risk anytime rope over 3/4-inch is needed.

"Below 5/8-inch rope heating due to cycling is probably not an important factor; failure will be due to something else. Beginning at 3/4-inch moving upwards, it can be very important, since the larger rope can not cool as easily. The myth seems plausible."
__________________
Gear Testing--Engineering--Sailing
https://sail-delmarva.blogspot.com/
thinwater is offline   Reply With Quote
Old 25-05-2013, 08:14   #70
always in motion is the future
 
s/v Jedi's Avatar

Cruisers Forum Supporter

Join Date: Feb 2009
Location: in paradise
Boat: Sundeer 64
Posts: 19,779
Re: Rolling Hitch on Snubber

It's getting pretty messed up in this thread

Quote:
Originally Posted by Dockhead View Post
It's not the snubber we're worrying about releasing -- it's the chain strop or whatever is used to belay the chain ahead of the windlass. I presume you use something like this? Maybe you have a chain lock, which some people use for this purpose? I sure hope you have something besides your snubber between your chain and your windlass . . .
Sure I have and would guess you know that: a chain stopper. It's made for the job. There is no drama or releasing tension or anything like that; the snubber has the tension, the chain is laying slack through the chain stopper and I only need to lift the pawl and that's it. It is the people who do not use proper gear and thus start using shackles (with spanners and all!) or ropes tied to chains to make up for lack of a chain stopper that get in trouble on that front. For many, the thought about how to deal with emergencies doesn't even come up and they will be clueless when that time comes... and it will one day.



Quote:
Originally Posted by transmitterdan View Post
Exactly right! Many people are "afraid" to use the correct snubber because it is small nylon 3-strand. We use New England 1/2" nylon 3-strand snubber on a Valiant 42. Jedi's snubber looks too big but may be right for his boat too. Depending on windage Hawk might want 5/8" nylon but probably not bigger than that. Our 1/2" nylon line breaking strength is more than the chain safe working load. This is a key parameter to consider in choosing a snubber. It should be the smallest line with breaking strength that exceeds the chain's safe working load.

For calm the snubber is 25 feet. For difficult conditions it is 50 feet with another 75 feet snubber behind it as backup. For hurricanes you need multiple anchor points anyway so we are ignoring that scenario in this discussion.

Nylon line will stretch to nearly twice it's normal length before breaking so I never put out enough loop of chain. We set the brake on the windlass somewhat so if the snubber stretches more than the chain loop then more chain will pay out of the windlass but stop when the snubber finally comes up short. Hearing the chain pay out will make me want to go up on deck and check things.

After a serious blow discard the snubber and use a new one. They are cheap and work perfectly.

There is no way I would use high tech climbing line as a snubber as it only serves to defeat the purpose of the snubber. A proper snubber has to stretch...a lot...to do its job.
Oh my, I'm afraid you got some things backwards... it is your snubber that is too big at 1/2". Mine is 5/8" which is only 1/8" more while my boat weighs 4 times yours I guess... Also, the climbers rope is designed to stretch while 3-strand does so because they couldn't make it better. Next it the length of your snubbers which is just way off. 125', really?? that means it will stretch to 250', you don't even have that much extra chain to spare, reducing it's usefulness. The diameter of the snubber should be reduced until it breaks during a 50 knot or so squall and then you go up one size and that's it. 30' is enough.
I have seen lots of people using snubbers that are too long and overthinking it all... I remember that many always had trouble with dragging anchors and try to make up for inadequate anchors. All IMHO of-course.

Quote:
Originally Posted by noelex 77 View Post
I think a must of offended the god of snubbers in a previous life because a well as my rolling hitches slipping, I break a least one snubber a year, usually a couple.

I am hoping its its the lousy nylon that sold here. The local fisherman buy more on price than quality.
I have just received some octiplat from the UK and I have my fingers crossed for no more broken snubbers.
That's what you get for trying to keep it cheap cheap cheap Test for minimum diameter with one solid brand and then stay with that brand. A snubber lasts for a year or more and only needs 30' of line to make, so once you know which line, buy 120' of it, splice 4 snubbers from it and you're done for a decade

Octoplait is better than 3-strand; it is the eye splice that keeps me away from it. I hate to spend that much time on it for piece that I consider chafing gear. I did an eye splice in my 1.25" octoplait secondary anchor rode and it took me the better part of a day... within a year I had to cut it off during an emergency

s/v Jedi is offline   Reply With Quote
Old 25-05-2013, 08:18   #71
Moderator
 
Dockhead's Avatar

Cruisers Forum Supporter

Join Date: Mar 2009
Location: Denmark (Winter), Cruising North Sea and Baltic (Summer)
Boat: Cutter-Rigged Moody 54
Posts: 35,020
Re: Rolling Hitch on Snubber

Quote:
Originally Posted by noelex 77 View Post
I think a must of offended the god of snubbers in a previous life because a well as my rolling hitches slipping, I break a least one snubber a year, usually a couple.

I am hoping its its the lousy nylon that sold here. The local fisherman buy more on price than quality.
I have just received some octiplat from the UK and I have my fingers crossed for no more broken snubbers.
If your rolling hitch slips -- a very unusual problem -- try tying an extra turn in it, and/or tying off the the tail with a clove hitch or a couple of half-hitches. It should form into the chain and be absolutely secure. You could also try some of the other knots suggested, but keep in mind that few knots compromise the strength of the rope less than a rolling hitch, which is almost as good as a splice for strength (n.b. that strength and security are completely different qualities in a knot; the rolling hitch is not particularly secure), about 60%.

If your snubbers are breaking, then something is wrong. Is the size ok? Are they breaking somewhere where they might be chafing on something?

I've only ever broken one, and that was my own d*mn fault. It was when I first acquired my boat, and was still using a ridiculously skinny (probably 12mm or at most 14mm) and short snubber inherited from the PO. I was anchored in Studland Bay in a gale which decided to veer 180 degrees during the night, removing all shelter, putting us off a lee shore in the surf, and buffeting us with big waves, some of them actually breaking. The snubber broke. Thank God I had belayed the chain with a stout strop, which saved my boat and possibly my life. Unaware that the snubber was broken (I should have checked), and not wanting to work on the heaving foredeck in the stormy dark, I waited until morning to do anything. Yikes. I would do it all differently today.
Dockhead is offline   Reply With Quote
Old 25-05-2013, 08:20   #72
Moderator
 
noelex 77's Avatar

Cruisers Forum Supporter

Join Date: Jul 2007
Boat: Bestevaer.
Posts: 15,161
Re: Rolling Hitch on Snubber

Quote:
Originally Posted by Kettlewell View Post
Where do they break?
No consistent spot.
The last one broke only a couple of feet from the Samson post where it is secured. At this point it was inside some water water hose that I use for chafe protection. There may have been some extra heating and friction, but the one before broke at the other end.
It is a nusance but not a big problem. They go with a tremendous bang, so it is easy to tell what has happened. I have second very thick metre long "snubber" attached to the Samson post that transfers the shock load of the boat surging backwards to the strongest part of the boat.
noelex 77 is offline   Reply With Quote
Old 25-05-2013, 08:30   #73
Moderator
 
Dockhead's Avatar

Cruisers Forum Supporter

Join Date: Mar 2009
Location: Denmark (Winter), Cruising North Sea and Baltic (Summer)
Boat: Cutter-Rigged Moody 54
Posts: 35,020
Re: Rolling Hitch on Snubber

Quote:
Originally Posted by s/v Jedi View Post
Sure I have and would guess you know that: a chain stopper. It's made for the job. There is no drama or releasing tension or anything like that; the snubber has the tension, the chain is laying slack through the chain stopper and I only need to lift the pawl and that's it. It is the people who do not use proper gear and thus start using shackles (with spanners and all!) or ropes tied to chains to make up for lack of a chain stopper that get in trouble on that front. For many, the thought about how to deal with emergencies doesn't even come up and they will be clueless when that time comes... and it will one day.




A chain stopper is a great solution, of course, provided, however, that you are able to install it in a strong enough spot. I have not yet figured that out on my boat, which has a balsa-cored deck, which is why I use a devil's-claw like technique like on a ship (my arrangement looks quite like the deck of the Royal Navy frigate in the drawing I posted a few pages back). The downside of a chain stopper is that it is probably not possible to make it as strong as a proper chain strop on a boat with a fiberglass deck; the upside is that it is extremely convenient and a cinch to release in an emergency. My father's boat has one.

I would disagree, however, that belaying the chain other than by using a stopper is "improper gear". A chain strop is a traditional and proper technique, as is a devil's claw, both used on large ships as well as on yachts for centuries. You are correct, however, that one must think about how to quickly release whatever it is you're using, and I confess to not having thought that through adequately until now.
Dockhead is offline   Reply With Quote
Old 25-05-2013, 08:35   #74
Registered User
 
Cotemar's Avatar

Community Sponsor

Join Date: Dec 2007
Boat: Mahe 36, Helia 44 Evo, MY 37
Posts: 5,731
Re: Rolling Hitch on Snubber

I think Evans Starzinger “Get a Grip!” article in BoatUS may help here.
It covers the Rolling Hitch, Modified Rolling Hitch (Camel Hitch) and the Icicle Hitch

http://www.boatus.com/magazine/2013/June/get-a-grip.asp
Attached Thumbnails
Click image for larger version

Name:	Icicle_Hitch.jpg
Views:	147
Size:	16.8 KB
ID:	61329  
Attached Files
File Type: pdf Icicle_Hitch.pdf (246.3 KB, 78 views)
Cotemar is offline   Reply With Quote
Old 25-05-2013, 08:40   #75
Pusher of String
 
foolishsailor's Avatar

Cruisers Forum Supporter

Join Date: Feb 2007
Location: On the hard; Trinidad
Boat: Trisbal 42, Aluminum Cutter Rigged Sloop
Posts: 2,314
Images: 19
Any method of belaying that involves line is inherently quick release and a proper method - even if not as "efficient" as a chain stop. All one has to do with line in an emergency is to apply something with a sharp edge.

I still prefer a loop and prusik knot for my chain as I can pull the chain over my bow roller with the loop in. Maybe just lazy I guess.
__________________
"So, rather than appear foolish afterward, I renounce seeming clever now."
William of Baskerville

"You will do foolish things, but do them with enthusiasm."
Sidonie Gabrielle Colette
foolishsailor is offline   Reply With Quote
Reply

Thread Tools Search this Thread
Search this Thread:

Advanced Search
Display Modes Rate This Thread
Rate This Thread:

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off
Trackbacks are Off
Pingbacks are Off
Refbacks are Off


Similar Threads
Thread Thread Starter Forum Replies Last Post
Challenge: How to Stop Rolling at Anchor captainKJ Challenges 49 25-05-2013 00:52
Fairleading the Snubber cfarrar Anchoring & Mooring 15 01-02-2013 12:00
How to rig a snubber ona bobstay boat BlackOak Monohull Sailboats 6 01-02-2013 08:24
Hitch Ride from Florida to Cuba RavennaSailor Our Community 4 18-12-2012 18:45
Hitch Hiking from Puerto Rico to Venezuela ondi Atlantic & the Caribbean 5 23-07-2011 13:21

Advertise Here


All times are GMT -7. The time now is 16:58.


Google+
Powered by vBulletin® Version 3.8.8 Beta 1
Copyright ©2000 - 2024, vBulletin Solutions, Inc.
Social Knowledge Networks
Powered by vBulletin® Version 3.8.8 Beta 1
Copyright ©2000 - 2024, vBulletin Solutions, Inc.

ShowCase vBulletin Plugins by Drive Thru Online, Inc.