|
Click Here to Login |
Community Links |
Social Groups |
Pictures & Albums |
Members List |
Meet the Mods |
Meet the Advisors |
Signup for The Daily Cruiser Email |
Search Forums | |||||
Tag Search | |||||
Advanced Search |
Showing results 1 to 13 of 13
Search took 0.00 seconds. Search: Posts Made By: summerlove |
Forum: Liveaboard's Forum 22-01-2018, 09:49 |
Replies: 56
Views: 19,607
Posted By
summerlove
Re: Boat wide Wi-Fi with surveillance cameras, Internet and Garmin gpsmap 7000 serie
has anyone tried using this on raymarine e80 to get wifi accessibility from ipad |
Forum: Vendor Spotlight - Great Deals for CF Members! 22-01-2018, 07:56 |
Replies: 233
Views: 128,094
Posted By
summerlove
|
Forum: Our Community 22-01-2018, 07:47 |
Replies: 14
Views: 3,509
Posted By
summerlove
|
Forum: Electrical: Batteries, Generators & Solar 22-01-2018, 06:28 |
Replies: 22
Views: 7,573
Posted By
summerlove
Re: Solar Panels - Wire in Series, or Parrallel ?
my solar panels charge my batteries for my dc refrigeration system, my wind generator charges my house battery, my engine is charging the engine battery....I have three separate battery banks...the... |
Forum: Marine Electronics 31-07-2013, 16:03 |
Replies: 25
Views: 3,271
Posted By
summerlove
Re: which tablet?
I use iPad with a blue tooth gps unit and Garmin bluechart works flawlessly. Lasts about 4-5 hours but I have it connected directly to dc. I use it hand in hand with my Garmin 4212 to see if there... |
Forum: Engines and Propulsion Systems 09-03-2013, 06:28 |
Replies: 9
Views: 3,234
Posted By
summerlove
Re: Yanmar 2gm20 fwc
Sorry for the delay in responding...cleaned the injectors and replaced with new seals, temperature of engine and day was 34 degrees..purged air from lines..tightened the fuel lines proceeded to start... |
Forum: Engines and Propulsion Systems 05-01-2013, 06:36 |
Replies: 21
Views: 5,490
Posted By
summerlove
Re: 2gm20f Not Running After Topping Fuel
If you remove the bleedscrew from the top of the engine filter, you should try using a vacuum pump, like the one you use for your oil change, to this opening to draw up the fuel. If nothing comes out... |
Forum: Engines and Propulsion Systems 19-12-2012, 14:58 |
Replies: 9
Views: 3,234
Posted By
summerlove
Ok tested compression with special tool...
Ok tested compression with special tool compression at 420 psi each cylinder Took out injectors for cleaning and repair |
Forum: Engines and Propulsion Systems 16-11-2012, 04:45 |
Replies: 9
Views: 3,234
Posted By
summerlove
Yanmar 2gm20 fwc
On Long Island,ny when it gets cold 40/50 engine hard starting. When it does start vibration and valve tapping sound increase rpm to 1400 and it starts to smooth down till warm but still has some... |
Forum: Electrical: Batteries, Generators & Solar 27-03-2012, 08:33 |
Replies: 72
Views: 8,719
Posted By
summerlove
In addition, the ac load panel area needs a shore...
In addition, the ac load panel area needs a shore power gen power switch if you intend to connect it all boat ac outlets. A circuit breaker recommended inline to switch. DC cable routing watch for... |
Forum: Electrical: Batteries, Generators & Solar 27-03-2012, 06:17 |
Replies: 72
Views: 8,719
Posted By
summerlove
I completed a task similar to yours. The biggest...
I completed a task similar to yours. The biggest problem that I needed help with was the battery installation......two man job on my 30 ft hunter. Tha heavy cable routing to the inverter can be an... |
Forum: Electrical: Batteries, Generators & Solar 03-06-2011, 10:52 |
Replies: 22
Views: 7,573
Posted By
summerlove
Re: Solar Panels - Wire in Series, or Parrallel ?
regarding parallel vs series wiring, 1 the typical voltage as messured at the panel is apox 17/19 for parallel and 34/38 volts 2 the current for parallel is double the spec for the solar panel... |
Forum: Navigation 11-03-2011, 03:46 |
Replies: 6
Views: 3,437
Posted By
summerlove
Re: MaxSea on Laptop - Set-Up Help, Please
Since u did not mention which computer you are using, I should mention that some programs want to communicate with com1. Your computer may have com1 assigned to the IR port...disable the IR port and... |
Showing results 1 to 13 of 13 |
Powered by vBulletin® Version 3.8.8 Beta 1
Copyright ©2000 - 2024, vBulletin Solutions, Inc. |
Privacy Guaranteed - your email is never shared with anyone, opt out any time.