Cruisers Forum

Join CruisersForum Today

Thread Tools Rate Thread Display Modes
Old 08-04-2016, 18:43   #1
Registered User

Join Date: Nov 2013
Posts: 45
Oil leaking on oil pan gasket

After replacing of rod bearings on crank shaft. I did bad work with oil pan gaskets. It is made of set of three gaskets. The long ones from harder material
are okay. But front and rear gasket are leaking. I could see it in front and when i was pushing with finger on gasket it was soft and drop of oil did come out then.

But what worries me more is the other gasket at the back side. After the three hours of engine running i could see oil on a wheel through the hole in transmission.

I am in Guatemala now.I think i could go on to reach the USA and do the work there, but is it not the a clutch on the wheel, and will it not start to slide once the oil will reach her?
And how can i pump out now the oil.?

I did the work by elevating of engine as much i could and then working laying in the bilge under. When i am thinking now i remember that i had to push hard to get gasket in the channel. it is becoming clear to me now that i did lose volume of gasket doing it. I did not remove any other elements of the engine and it is that i am getting the picture now, that other elements then push on gasket to make them larger in direction where oil pan is pressing.

And what would be the best way to come out of this situation?
Attached Thumbnails
Click image for larger version

Name:	DSC02179.jpg
Views:	83
Size:	441.4 KB
ID:	122272  
pr2501 is offline   Reply With Quote
Old 09-04-2016, 00:08   #2
Registered User

Join Date: Oct 2009
Location: australia
Posts: 503
Re: Oil leaking on oil pan gasket

That is the drive plate you can see, it soaks up any torsional vibrations etc between motor and Gearbox, your Borg Warner box input shaft spigots into the drive plate centre it cannot slip.
I assume you used the old gaskets that have grown due to compression & age, replacement is really the only reliable fix however a correctly prepared surface and sikaflex or a similar product may give a short term fix. If you use a sealant be careful not to contaminate the lube oil with it.
shakey doug is offline   Reply With Quote
Old 10-04-2016, 09:36   #3
Registered User

Join Date: Nov 2013
Posts: 45
Re: Oil leaking on oil pan gasket

Ok. It means that i can go on. I will do the work later.

Thank you.
pr2501 is offline   Reply With Quote

gasket, oil, oil leak

Thread Tools
Display Modes Rate This Thread
Rate This Thread:

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off
Trackbacks are Off
Pingbacks are Off
Refbacks are Off

Similar Threads
Thread Thread Starter Forum Replies Last Post
PAN PAN....OR PON PON Mark1977 Our Community 247 08-10-2016 01:17
When to use Mayday-Pan-Pan and Securite ASD Health, Safety & Related Gear 0 20-10-2015 09:15
The trip... Securite.. as opposed to Pan Pan or Mayday.. blah blah blah boatman61 General Sailing Forum 281 15-04-2014 06:08
Leaking Intake Gasket Caused by Too Much Blow-By? Killick Engines and Propulsion Systems 4 18-08-2009 21:08

Copyright 2002- Social Knowledge, LLC All Rights Reserved.

All times are GMT -7. The time now is 07:56.

Powered by vBulletin® Version 3.8.8 Beta 1
Copyright ©2000 - 2018, vBulletin Solutions, Inc.
Social Knowledge Networks
Powered by vBulletin® Version 3.8.8 Beta 1
Copyright ©2000 - 2018, vBulletin Solutions, Inc.

ShowCase vBulletin Plugins by Drive Thru Online, Inc.