Cruisers Forum
 


Join CruisersForum Today

Reply
 
Thread Tools Rate Thread Display Modes
Old 11-12-2017, 09:20   #1
Registered User

Join Date: Feb 2015
Location: Certosa Marina, Venice
Boat: Jeanneau 43ds
Posts: 184
Send a message via Skype™ to SaltyMetals
Prop shaft and taper details for a Jeanneau 43ds

I would like to change my prop to feathering/folding but am not quite sure of the shaft diameter and taper details. I think the diameter is 1 3/8" (38mm) but am i wrong?Is it 35mm? It also appears that the taper characteristics are often according to the ISO35 standard but does that apply to ALL Jeanneau boats of this size?
Anybody got any ideas?
Andrew
"Genial Bee"
__________________

__________________
SaltyMetals is offline   Reply With Quote
Old 11-12-2017, 09:43   #2
Registered User

Join Date: Oct 2015
Posts: 300
Re: Prop shaft and taper details for a Jeanneau 43ds

Quote:
Originally Posted by SaltyMetals View Post
I would like to change my prop to feathering/folding but am not quite sure of the shaft diameter and taper details. I think the diameter is 1 3/8" (38mm) but am i wrong?Is it 35mm? It also appears that the taper characteristics are often according to the ISO35 standard but does that apply to ALL Jeanneau boats of this size?
Anybody got any ideas?
Andrew
"Genial Bee"
1 3/8" is very close to 35mm, not 38. But they are not the interchangable. For what it is worth, I have worked on several Jeanneau's and they all had metric shafts.

But I wouldn't spend any of my money based on anything EXCEPT putting a caliper on the shaft of my boat.

But you might trust the internet more than I do...
__________________

__________________
billknny is offline   Reply With Quote
Old 12-12-2017, 00:52   #3
Sponsoring Vendor
 
EWOL Props's Avatar

Community Sponsor

Join Date: Nov 2015
Posts: 86
Re: Prop shaft and taper details for a Jeanneau 43ds

Quote:
Originally Posted by SaltyMetals View Post
I would like to change my prop to feathering/folding but am not quite sure of the shaft diameter and taper details. I think the diameter is 1 3/8" (38mm) but am i wrong?Is it 35mm? It also appears that the taper characteristics are often according to the ISO35 standard but does that apply to ALL Jeanneau boats of this size?
Anybody got any ideas?
Andrew
"Genial Bee"
Hi Andrew, all the Jeanneau have metric standard shafts, so it is either a 30 mm or a 35 mm standard ISO 1:10 taper.
In the past we have supplied the Sun Odyssey 43 some few times, it was ISO 35 (or sail-drive)
EWOL Props is offline   Reply With Quote
Old 13-12-2017, 13:40   #4
Marine Service Provider
 
fstbttms's Avatar

Cruisers Forum Supporter

Join Date: Oct 2006
Location: Under a boat, in a marina, in the San Francisco Bay
Posts: 3,602
Re: Prop shaft and taper details for a Jeanneau 43ds

Quote:
Originally Posted by SaltyMetals View Post
I would like to change my prop to feathering/folding but am not quite sure of the shaft diameter and taper details. I think the diameter is 1 3/8" (38mm) but am i wrong?Is it 35mm? It also appears that the taper characteristics are often according to the ISO35 standard but does that apply to ALL Jeanneau boats of this size?
Anybody got any ideas?
All metric shafts are sized in increments of 5mm. 20mm, 25mm, 30mm, 35mm etc. You get the picture. There are no metric shafts that are 38mm or whatever.
__________________
fstbttms is offline   Reply With Quote
Old 13-12-2017, 15:30   #5
Registered User

Join Date: Feb 2015
Location: Certosa Marina, Venice
Boat: Jeanneau 43ds
Posts: 184
Send a message via Skype™ to SaltyMetals
Re: Prop shaft and taper details for a Jeanneau 43ds

Yes, I think my shaft is 35mm but I was confused by the fact that I hv been buying shaft anodes for 38mm. Maybe Bill is right. I need to get a caliper on my shaft to see what it really is.
Many thanks guys for your comments and advice
Andrew
"Genial Bee" .
__________________
SaltyMetals is offline   Reply With Quote
Old 13-12-2017, 15:46   #6
Marine Service Provider
 
fstbttms's Avatar

Cruisers Forum Supporter

Join Date: Oct 2006
Location: Under a boat, in a marina, in the San Francisco Bay
Posts: 3,602
Re: Prop shaft and taper details for a Jeanneau 43ds

Quote:
Originally Posted by SaltyMetals View Post
I hv been buying shaft anodes for 38mm.
I guarantee you have never bought a 38mm shaft anode. They do not exist.
__________________
fstbttms is offline   Reply With Quote
Old 13-12-2017, 16:33   #7
Registered User

Join Date: Feb 2015
Location: Certosa Marina, Venice
Boat: Jeanneau 43ds
Posts: 184
Send a message via Skype™ to SaltyMetals
Re: Prop shaft and taper details for a Jeanneau 43ds

Absurdly correct. I checked some of my docs. Definitely I hv 35 mm diameter shaft. Is the taper ISO 35 or 1:10? Or are these the same thing?
__________________
SaltyMetals is offline   Reply With Quote
Old 14-12-2017, 00:34   #8
Sponsoring Vendor
 
EWOL Props's Avatar

Community Sponsor

Join Date: Nov 2015
Posts: 86
Re: Prop shaft and taper details for a Jeanneau 43ds

Same thing, the ISO35 is a 1:10 tapered end
EWOL Props is offline   Reply With Quote
Reply

Tags
jeanneau

Thread Tools
Display Modes Rate This Thread
Rate This Thread:

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off
Trackbacks are Off
Pingbacks are Off
Refbacks are Off


Similar Threads
Thread Thread Starter Forum Replies Last Post
steering wheel shaft taper damianham Construction, Maintenance & Refit 2 02-02-2015 03:20
Rocna anchor on a Jeanneau SO 43DS? HappyDaze Construction, Maintenance & Refit 2 18-10-2012 09:04
Recommendations for Electric Head for Jeanneau 43DS ? Susan French Plumbing Systems and Fixtures 19 10-05-2011 22:06
Wanted mast and rigging for Jeanneau 43DS dkstock Classifieds Archive 5 22-10-2008 19:07
where can i get a used mast for a Jeanneau 43DS dkstock Deck hardware: Rigging, Sails & Hoisting 0 28-09-2008 06:12



Copyright 2002- Social Knowledge, LLC All Rights Reserved.

All times are GMT -7. The time now is 10:44.


Google+
Powered by vBulletin® Version 3.8.8 Beta 1
Copyright ©2000 - 2018, vBulletin Solutions, Inc.
Social Knowledge Networks
Powered by vBulletin® Version 3.8.8 Beta 1
Copyright ©2000 - 2018, vBulletin Solutions, Inc.

ShowCase vBulletin Plugins by Drive Thru Online, Inc.